参数资料
| 型号： | AD8426ACPZ-WP |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP INSTR RR 1.5MHZ 16LFCSP |
| 标准包装： | 64 |
| 放大器类型： | 仪表 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.6 V/µs |
| -3db带宽： | 1MHz |
| 电流 - 输入偏压： | 20nA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 350µA |
| 电流 - 输出 / 通道： | 13mA |
| 电压 - 电源，单路/双路(±)： | 2.2 V ~ 36 V，±1.35 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN，CSP |
| 供应商设备封装： | 16-LFCSP（4x4） |
| 包装： | 托盘 - 晶粒 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8426
Rev. 0 | Page 22 of 28
REFERENCE TERMINAL
The output voltage of the AD8426 is developed with respect
to the potential on the reference terminal. This is useful when
the output signal needs to be offset to a precise midsupply level.
For example, a voltage source can be tied to the REF pin to level-
shift the output so that the AD8426 can drive a single-supply
ADC. The REF pin is protected with ESD diodes and should
not exceed either +VS or VS by more than 0.3 V.
For the best performance, source impedance to the REF
terminal should be kept below 2 Ω. As shown in Figure 62,
the reference terminal, REF, is at one end of a 50 kΩ resistor.
Additional impedance at the REF terminal adds to this 50 kΩ
resistor and results in amplification of the signal connected to
the positive input. The amplification from the additional RREF
can be computed by 2 × (50 kΩ + RREF)/100 kΩ + RREF.
Only the positive signal path is amplified; the negative path is
unaffected. This uneven amplification degrades the CMRR of
the amplifier.
CORRECT
AD8426
OP1177
+
–
CORRECT
AD8426
+
–
REF
INCORRECT
VREF
AD8426
REF
09
49
0-
15
6
Figure 62. Driving the Reference Pin
INPUT VOLTAGE RANGE
The 3-op-amp architecture of the AD8426 applies gain in
the first stage before removing common-mode voltage in the
difference amplifier stage. In addition, the input transistors in
the first stage shift the common-mode voltage up one diode
drop. Therefore, internal nodes between the first and second
stages (Node 1 and Node 2 in Figure 61) experience a combina-
tion of gained signal, common-mode signal, and a diode drop.
This combined signal can be limited by the voltage supplies even
when the individual input and output signals are not limited.
mode input voltage ranges for various output voltages and
supply voltages.
Equation 1 to Equation 3 can be used to understand the inter-
action of the gain (G), common-mode input voltage (VCM),
differential input voltage (VDIFF), and reference voltage (VREF).
The values for the constants (VLIMIT, V+LIMIT, and VREF_LIMIT)
at different temperatures are shown in Table 12. These three
equations, along with the input and output voltage range speci-
of the part.
LIMIT
S
DIFF
CM
V
G
V
+
>
×
2
(1)
LIMIT
S
DIFF
CM
V
G
V
+
+
<
×
+
2
(2)
REF_LIMIT
S
REF
CM
DIFF
V
G
V
+
<
+
×
2
(3)
Table 12. Input Voltage Range Constants for Various
Temperatures
Temperature
VLIMIT (V)
V+LIMIT (V)
VREF_LIMIT (V)
40°C
0.55
+0.8
+1.3
+25°C
0.35
+0.7
+1.15
+85°C
0.15
+0.65
+1.05
+125°C
0.05
+0.6
+0.9
The common-mode input voltage range shifts upward with temp-
erature. At cold temperatures, the part requires extra headroom
from the positive supply, whereas operation near the negative
supply has more margin. Conversely, at hot temperatures, the part
requires less headroom from the positive supply but is subject
to the worst-case conditions for input voltages near the negative
supply.
A typical part functions up to the boundaries described in this
section. However, for best performance, designing with a few
hundred millivolts of extra margin is recommended. As signals
approach the boundary, internal transistors begin to saturate,
which can affect frequency and linearity performance.
相关PDF资料 |
PDF描述 |
|---|---|
| TSW-124-14-T-S | CONN HEADER 24POS .100" SNGL TIN |
| AD8642ARZ | IC OPAMP JFET R-R 3.5MHZ 8SOIC |
| LT1002CN#PBF | IC PREC OPAMP DUAL MATCHED 14DIP |
| TSW-105-14-S-S | CONN HEADER 5POS .100" SGL GOLD |
| TSW-102-08-L-D-RA | CONN HEADER 4POS .100 DL R/A AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8426BCPZ-R7 | 功能描述:IC AMP INSTR RR 1.5MHZ 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD8426BCPZ-R7_PROMO | 制造商:Analog Devices 功能描述:INSTR-AMPLIFIER 1MHZ 90DB L |
| AD8426BCPZ-WP | 功能描述:IC AMP INSTR RR 1.5MHZ 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD8428 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 |
| AD8428_12 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 |
发布紧急采购，3分钟左右您将得到回复。