参数资料
| 型号： | AD8426ACPZ-WP |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP INSTR RR 1.5MHZ 16LFCSP |
| 标准包装： | 64 |
| 放大器类型： | 仪表 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.6 V/µs |
| -3db带宽： | 1MHz |
| 电流 - 输入偏压： | 20nA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 350µA |
| 电流 - 输出 / 通道： | 13mA |
| 电压 - 电源，单路/双路(±)： | 2.2 V ~ 36 V，±1.35 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN，CSP |
| 供应商设备封装： | 16-LFCSP（4x4） |
| 包装： | 托盘 - 晶粒 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8426
Rev. 0 | Page 23 of 28
LAYOUT
To ensure optimum performance of the AD8426 at the PCB
level, care must be taken in the design of the board layout.
The AD8426 pins are arranged in a logical manner to aid in
this task.
1
2
3
4
12
11
10
9
5
678
13
14
15
16
–IN1
+IN1
RG1
AD8426
+V
S
OU
T
1
OU
T
2
–V
S
–IN2
+IN2
RG2
+V
S
–V
S
RE
F
1
RE
F
2
09
49
0-
0
2
Figure 63. Pinout Diagram
Package Considerations
The AD8426 is available in a 16-lead, 4 mm × 4 mm LFCSP with
no exposed paddle. The footprint from another 4 mm × 4 mm
LFCSP part should not be copied because it may not have the
correct lead pitch and lead width dimensions. Refer to the
Outline Dimensions section to verify that the corresponding
dimensional symbol has the correct dimensions.
Hidden Paddle Package
The AD8426 is available in an LFCSP package with a hidden
paddle. Unlike chip scale packages where the pad limits routing
capability, this package allows routes and vias directly beneath
the chip. In this way, the full space savings of the small LFCSP
can be realized. Although the package has no metal in the center
of the part, the manufacturing process leaves a very small section
of exposed metal at each of the package corners, as shown in
This metal is connected to VS through the part. Because of the
possibility of a short, vias should not be placed beneath these
exposed metal tabs.
0
949
0-
1
58
HIDDEN
PADDLE
EXPOSED METAL
TABS
BOTTOM VIEW
NOTES
1. EXPOSED METAL TABS AT THE FOUR
CORNERS OF THE PACKAGE ARE
INTERNALLY CONNECTED TO –VS.
Figure 64. Hidden Paddle Package, Bottom View
Common-Mode Rejection Ratio over Frequency
Poor layout can cause some of the common-mode signals to be
converted to differential signals before reaching the in-amp. Such
conversions occur when one input path has a frequency response
that is different from the other. To keep CMRR over frequency
high, the input source impedance and capacitance of each path
should be closely matched. Additional source resistance in the
input paths (for example, for input protection) should be placed
close to the in-amp inputs to minimize the interaction of the
inputs with parasitic capacitance from the PCB traces.
Parasitic capacitance at the gain setting pins can also affect CMRR
over frequency. If the board design has a component at the gain
setting pins (for example, a switch or jumper), the component
should be chosen so that the parasitic capacitance is as small as
possible.
Power Supplies
A stable dc voltage should be used to power the instrumenta-
tion amplifier. Noise on the supply pins can adversely affect
performance. See the PSRR performance curves in Figure 22
and Figure 25 for more information.
A 0.1 μF capacitor should be placed as close as possible to each
supply pin. As shown in Figure 65, a 10 μF capacitor can be used
farther away from the part. In most cases, it can be shared by
other precision integrated circuits.
AD8426
+VS
+IN
–IN
LOAD
REF
0.1F
10F
0.1F
10F
–VS
OUT
0
949
0-
0
06
RG
Figure 65. Supply Decoupling, REF, and Output Referred to Local Ground
References
The output voltage of the AD8426 is developed with respect to
the potential on the reference terminal. Care should be taken to
tie the REFx pins to the appropriate local ground. This should
also help minimize crosstalk between the two channels.
相关PDF资料 |
PDF描述 |
|---|---|
| TSW-124-14-T-S | CONN HEADER 24POS .100" SNGL TIN |
| AD8642ARZ | IC OPAMP JFET R-R 3.5MHZ 8SOIC |
| LT1002CN#PBF | IC PREC OPAMP DUAL MATCHED 14DIP |
| TSW-105-14-S-S | CONN HEADER 5POS .100" SGL GOLD |
| TSW-102-08-L-D-RA | CONN HEADER 4POS .100 DL R/A AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8426BCPZ-R7 | 功能描述:IC AMP INSTR RR 1.5MHZ 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD8426BCPZ-R7_PROMO | 制造商:Analog Devices 功能描述:INSTR-AMPLIFIER 1MHZ 90DB L |
| AD8426BCPZ-WP | 功能描述:IC AMP INSTR RR 1.5MHZ 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD8428 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 |
| AD8428_12 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 |
发布紧急采购，3分钟左右您将得到回复。