- 您现在的位置：买卖IC网 > PDF目录10681 > AD9203ARUZ (Analog Devices Inc)IC ADC 10BIT 40MSPS 3V 28-TSSOP PDF资料下载
参数资料
| 型号： | AD9203ARUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 40MSPS 3V 28-TSSOP |
| 标准包装： | 50 |
| 位数： | 10 |
| 采样率（每秒）： | 40M |
| 数据接口： | 并联 |
| 转换器数目： | 5 |
| 功率耗散（最大）： | 108mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；1 个差分，单极 |
| 产品目录页面： | 780 (CN2011-ZH PDF) |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD9203
Rev. B | Page 12 of 28
INPUT AND REFERENCE OVERVIEW
Like the voltage applied to the top of the resistor ladder in a
flash A/D converter, the value VREF defines the maximum
input voltage to the A/D core. The minimum input voltage to
the A/D core is automatically defined to be VREF.
The addition of a differential input structure gives the user an
additional level of flexibility that is not possible with traditional
flash converters. The input stage allows the user to easily
configure the inputs for either single-ended operation or
differential operation. The A/D’s input structure allows the dc
offset of the input signal to be varied independently of the input
span of the converter. Specifically, the input to the A/D core is
the difference of the voltages applied at the AINP and AINN
input pins. Therefore, the equation,
VCORE = AINP AINN
(1)
defines the output of the differential input stage and provides
the input to the A/D core.
The voltage, VCORE, must satisfy the condition,
VREF ≤ VCORE ≤ VREF
(2)
where VREF is the voltage at the VREF pin.
The actual span (AINP AINN) of the ADC is ±VREF.
While an infinite combination of AINP and AINN inputs exist
that satisfy Equation 2, an additional limitation is placed on the
inputs by the power supply voltages of the AD9203. The power
supplies bound the valid operating range for AINP and AINN.
The condition,
AVSS 0.3 V < AINP < AVDD + 0.3 V
AVSS 0.3 V < AINN < AVDD + 0.3 V
(3)
where AVSS is nominally 0 V and AVDD is nominally 3 V,
defines this requirement. The range of valid inputs for AINP
and AINN is any combination that satisfies both Equations 2
and 3.
INTERNAL REFERENCE CONNECTION
A comparator within the AD9203 will detect the potential of
the VREF pin. If REFSENSE is grounded, the reference
amplifier switch will connect to the resistor divider (see Figure
19). That will make VREF equal to 1 V. If resistors are placed
between VREF, REFSENSE and ground, the switch will be
connected to the REFSENSE position and the reference
amplitude will depend on the external programming resistors
(Figure 21). If REFSENSE is tied to VREF, the switch will also
connect to REFSENSE and the reference voltage will be 0.5 V
(Figure 20). REFTF and REFBF will drive the ADC conversion
core and establish its maximum and minimum span. The range
of the ADC will equal twice the voltage at the reference pin for
either an internal or external reference.
Figure 19 illustrates the input configured with a 1 V reference.
This will set the single-ended input of the AD9203 in the 2 V
span (2 × VREF). This example shows the AINN input is tied to
the 1 V VREF. This will configure the AD9203 to accept a 2 V
input centered around 1 V.
00573-019
ADC
CORE
+
–
10
F
0.1
F
0.1
F
0.1
F
0.1
F
10
F
AINP
AINN
VREF
0.5V
REFTF
REFBF
REFSENSE
2V
0V
AD9203
2V
1V
LOGIC
Figure 19. Internal Reference Set for a 2 V Span
Figure 20 illustrates the input configured with a 0.5 V reference.
This will set the single-ended input of the ADC in a 1 V span
(2 × VREF). The AINN input is tied to the 0.5 VREF. This will
configure the AD9203 to accept a 1 V input centered around
0.5 V.
00573-
020
ADC
CORE
+
–
LOGIC
AINP
AINN
VREF
0.5V
REFTF
REFBF
REFSENSE
1V
0V
1.75V
1.25V
AD9203
0.1
F
0.1
F
0.1
F
0.1
F
10
F
10
F
Figure 20. Internal Reference Set for a 1 V Span
Figure 21 shows the reference programmed by external resistors
for 0.75 V. This will set the ADC to receive a 1.5 V span
centered about 0.75 V. The reference is programmed according
to the algorithm:
VREF = 0.5 V × [1 + (RA/RB)]
相关PDF资料 |
PDF描述 |
|---|---|
| LT1720IDD#TRPBF | IC COMPARATOR DUAL HS 3/5V 8-DFN |
| LT1720IDD#TR | IC COMPARATOR DUAL HS 3/5V 8-DFN |
| AD7277BUJZ-500RL7 | IC ADC 10BIT 3MSPS TSOT23-6 |
| LT1720IDD#PBF | IC COMPARATOR DUAL HS 3/5V 8-DFN |
| LT1720IDD | IC COMPARATOR DUAL HS 3/5V 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9203ARUZ | 制造商:Analog Devices 功能描述:IC ADC 10BIT 40MSPS 28TSSOP |
| AD9203ARUZ | 制造商:Analog Devices 功能描述:IC, ADC, 10BIT, 40MSPS, TSSOP-28 |
| AD9203ARUZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:10-Bit, 40 MSPS, 3 V, 74 mW A/D Converter |
| AD9203ARUZRL7 | 功能描述:IC ADC 10BIT CMOS 40MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD9203ARUZRL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:10-Bit, 40 MSPS, 3 V, 74 mW A/D Converter |
发布紧急采购，3分钟左右您将得到回复。