参数资料
型号: AD9523BCPZ
厂商: Analog Devices Inc
文件页数: 17/60页
文件大小: 0K
描述: IC INTEGER-N CLCK GEN 72LFCSP
标准包装: 1
类型: 时钟/频率发生器,扇出缓冲器(分配)
PLL:
主要目的: 以太网,光纤通道,SONET/SDH
输入: CMOS
输出: HSTL,LVCMOS,LVDS,LVPECL
电路数: 1
比率 - 输入:输出: 2:14
差分 - 输入:输出: 是/是
频率 - 最大: 1GHz
电源电压: 1.71 V ~ 3.465 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 72-VFQFN 裸露焊盘,CSP
供应商设备封装: 72-LFCSP-VQ(10x10)
包装: 托盘
配用: AD9523/PCBZ-ND - BOARD EVAL FOR AD9523
AD9523
Data Sheet
Rev. C | Page 24 of 60
CLOCK DISTRIBUTION
The clock distribution block provides an integrated solution for
generating multiple clock outputs based on frequency dividing
the PLL2 VCO divider output. The distribution output consists
of 14 channels (OUT0 to OUT13). Each of the output channels
has a dedicated divider and output driver, as shown in Figure 25.
The AD9523 also has the capability to route the VCXO output
to four of the outputs (OUT0 to OUT3).
Clock Dividers
The output clock distribution dividers are referred to as D0 to
D13, corresponding to output channels OUT0 through OUT13,
respectively. Each divider is programmable with 10 bits of division
depth that is equal to 1 to 1024. Dividers have duty cycle correction
to always give 50% duty cycle, even for odd divides.
Output Power-Down
Each of the output channels offers independent control of the
power-down functionality via the Channel 0 to Channel 13 control
registers (see Table 51). Each output channel has a dedicated
power-down bit for powering down the output driver. However,
if all 14 outputs are powered down, the entire distribution output
enters a deep sleep mode. Although each channel has a channel
power-down control signal, it may sometimes be desirable to
power down an output driver while maintaining the divider’s
synchronization with the other channel dividers. This is accom-
plished by placing the output in tristate mode (this works in
CMOS mode, as well).
Multimode Output Drivers
The user has independent control of the operating mode of each of
the fourteen output channels via the Channel 0 to Channel 13
control registers (see Table 51). The operating mode control
includes the following:
Logic family and pin functionality
Output drive strength
Output polarity
The four least significant bits (LSBs) of each of the 14 Channel 0
to Channel 13 control registers comprise the driver mode bits. The
mode value selects the desired logic family and pin functionality
of an output channel, as listed in Table 51. This driver design
allows a common 100 external resistor for all the different
driver modes of operation that are illustrated in Figure 26.
If the output channel is ac-coupled to the circuit to be clocked,
changing the mode varies the voltage swing to determine sensi-
tivity to the drive level. For example, in LVDS mode, a current of
3.5 mA causes a 350 mV peak voltage. Likewise, in LVPECL mode,
a current of 8 mA causes an 800 mV peak voltage at the 100 load
resistor. Using any termination other than those specified in the
results in damage or decrease end of life performance
In addition to the four mode bits, each of the 14 Channel 0 to
Channel 13 control registers includes the following control bits:
Invert divider output. Enables the user to choose between
normal polarity and inverted polarity. Normal polarity is the
default state. Inverted polarity reverses the representation of
Logic 0 and Logic 1, regardless of the logic family.
Ignore sync. Makes the divider ignore the SYNC signal
from any source.
Power-down channel. Powers down the entire channel.
Lower power mode.
Driver mode.
Channel divider.
Divider phase.
3.5mA/8mA
LVDS/LVPECL
ENABLED
HSTL
ENABLED
HSTL
ENABLED
50
P
N
P
100 LOAD
CM
VDD3_OUT[x:y]
1.25V LVDS
VDD – 1.3V LVPECL
CM
COMMON-MODE
CIRCUIT
+
08439-
031
Figure 26. Multimode Driver
Clock Distribution Synchronization
A block diagram of the clock distribution synchronization
functionality is shown in Figure 27. The synchronization
sequence begins with the primary synchronization signal,
which ultimately results in delivery of a synchronization strobe
to the clock distribution logic.
As indicated, the primary synchronization signal originates
from one of the following sources:
Direct synchronization source via the sync dividers bit (see
Register 0x232, Bit 0 in Table 55)
Device pin, SYNC (Pin 17)
An automatic synchronization of the divider is initiated the first
time that PLL2 locks after a power-up or reset event. Subsequent
lock/unlock events do not initiate a resynchronization of the
distribution dividers unless they are preceded by a power-down
or reset of the part. Both sources of the primary synchronization
signal are logic OR’d; therefore, any one of them can synchronize
the clock distribution output at any time.
相关PDF资料
PDF描述
AD9524BCPZ IC INTEGER-N CLCK GEN 48LFCSP
AD9540BCPZ-REEL7 IC CLOCK GEN/SYNTHESIZER 48LFCSP
AD9547BCPZ-REEL7 IC CLOCK GEN/SYNCHRONIZR 64LFCSP
AD9548BCPZ-REEL7 IC CLOCK GEN/SYNCHRONIZR 88LFCSP
AD9549ABCPZ-REEL7 IC CLOCK GEN/SYNCHRONIZR 64LFCSP
相关代理商/技术参数
参数描述
AD9523BCPZ-REEL7 功能描述:IC INTEGER-N CLCK GEN 72LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP (0.240",6.10mm 宽) 供应商设备封装:64-TSSOP 包装:管件
AD9524 制造商:AD 制造商全称:Analog Devices 功能描述:Jitter Cleaner and Clock Generator with 6 Differential or 13 LVCMOS Outputs
AD9524/PCBZ 功能描述:BOARD EVAL FOR AD9524 RoHS:是 类别:编程器,开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理,热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板,CD,电源
AD9524BCPZ 功能描述:IC INTEGER-N CLCK GEN 48LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP (0.240",6.10mm 宽) 供应商设备封装:64-TSSOP 包装:管件
AD9524BCPZ-REEL7 功能描述:IC INTEGER-N CLCK GEN 48LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP (0.240",6.10mm 宽) 供应商设备封装:64-TSSOP 包装:管件