- 您现在的位置：买卖IC网 > PDF目录17063 > AD9748ACP-PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9748ACP PDF资料下载
参数资料
| 型号： | AD9748ACP-PCBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9748ACP |
| 产品培训模块： | DAC Architectures |
| 标准包装： | 1 |
| 系列： | TxDAC® |
| DAC 的数量： | 1 |
| 位数： | 8 |
| 采样率（每秒）： | 210M |
| 数据接口： | 并联 |
| 设置时间： | 11ns |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD9748 |
| 相关产品： | AD9748ACPZ-ND - IC DAC 8BIT 210MSPS 32-LFCSP |
Data Sheet
AD9748
Rev. B | Page 15 of 24
APPLYING THE AD9748
Output Configurations
The following sections illustrate some typical output
configurations for the AD9748. Unless otherwise noted, it is
assumed that IOUTFS is set to a nominal 20 mA. For applications
requiring the optimum dynamic performance, a differential
output configuration is suggested. A differential output
configuration can consist of either an RF transformer or a
differential op amp configuration. The transformer configuration
provides the optimum high frequency performance and is
recommended for any application that allows ac coupling. The
differential op amp configuration is suitable for applications
requiring dc coupling, bipolar output, signal gain, and/or
level shifting within the bandwidth of the chosen op amp.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage
results if IOUTA and/or IOUTB is connected to an appropriately
sized load resistor, RLOAD, referred to ACOM. This configuration
can be more suitable for a single-supply system requiring a dc-
coupled, ground referred output voltage. Alternatively, an
amplifier could be configured as an I-V converter, thus
converting IOUTA or IOUTB into a negative unipolar voltage.
This configuration provides the best dc linearity because
IOUTA or IOUTB is maintained at a virtual ground.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 25. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral
content lies within the transformer’s pass band. An RF transformer,
such as the Mini-Circuits T1–1T, provides excellent rejection of
common-mode distortion (that is, even-order harmonics) and
noise over a wide frequency range. It also provides electrical
isolation and the ability to deliver twice the power to the load.
Transformers with different impedance ratios can also be used
for impedance matching purposes. Note that the transformer
provides ac coupling only.
RLOAD
AD9748
MINI-CIRCUITS
T1-1T
OPTIONAL RDIFF
IOUTA
IOUTB
032
1
1-
022
Figure 25. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to ACOM to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages
appearing at IOUTA and IOUTB (that is, VOUTA and VOUTB)
swing symmetrically around ACOM and should be maintained
with the specified output compliance range of the AD9748. A
differential resistor, RDIFF, can be inserted in applications where
the output of the transformer is connected to the load, RLOAD,
via a passive reconstruction filter or cable. RDIFF is determined
by the transformer’s impedance ratio and provides the proper
source termination that results in a low VSWR. Note that
approximately half the signal power is dissipated across RDIFF.
相关PDF资料 |
PDF描述 |
|---|---|
| GCM18DCTD-S288 | CONN EDGECARD 36POS .156 EXTEND |
| GBM24DSEI-S243 | CONN EDGECARD 48POS .156 EYELET |
| GBM15DSEF-S243 | CONN EDGECARD 30POS .156 EYELET |
| GCM10DCST-S288 | CONN EDGECARD 20POS .156 EXTEND |
| SEK332M016ST | CAP ALUM 3300UF 16V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9748ACPRL7 | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 8-bit 32-Pin LFCSP EP T/R |
| AD9748ACPZ | 功能描述:IC DAC 8BIT 210MSPS 32-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD9748ACPZ | 制造商:Analog Devices 功能描述:DAC, 8BIT, 210MSPS, LFCSP-32 |
| AD9748ACPZRL7 | 功能描述:IC DAC 8BIT 210MSPS 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD9748XCP | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Bit, 165 MSPS TxDAC D/A Converter |
发布紧急采购，3分钟左右您将得到回复。