- 您现在的位置：买卖IC网 > PDF目录10978 > AD9838ACPZ-RL7 (Analog Devices Inc)IC DDS 16MHZ LOW PWR 20LFCSP PDF资料下载
参数资料
| 型号： | AD9838ACPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC DDS 16MHZ LOW PWR 20LFCSP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 标准包装： | 1,500 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 5MHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD9838
Rev. A | Page 24 of 32
APPLICATIONS INFORMATION
The various output options available from the AD9838 make
the part suitable for a wide variety of applications, including
modulation applications. The AD9838 can be used to perform
simple modulation, such as frequency shift keying (FSK). More
complex modulation schemes, such as Gaussian minimum shift
keying (GMSK) and quadrature phase shift keying (QPSK), can
also be implemented using the AD9838.
In an FSK application, the two frequency registers of the AD9838
are loaded with different values. One frequency represents the
space frequency, and the other represents the mark frequency. The
digital data stream is fed to the FSELECT pin, causing the AD9838
to modulate the carrier frequency between the two values.
The AD9838 has two phase registers, enabling the part to per-
form phase shift keying (PSK). With PSK, the carrier frequency
is phase shifted, that is, the phase is altered by an amount that
is related to the bit stream input to the modulator.
The AD9838 is also suitable for signal generator applications.
Using the on-board comparator, the device can be used to gen-
erate a square wave.
With its low current consumption, the part is also suitable for
applications in which it can be used as a local oscillator.
GROUNDING AND LAYOUT
The printed circuit board that houses the AD9838 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the use
of ground planes that can be separated easily. A minimum etch
technique is generally best for ground planes because it provides
the best shielding. Digital and analog ground planes should be
joined in one place only. If the AD9838 is the only device that
requires an AGND to DGND connection, the ground planes
should be connected at the AGND and DGND pins of the
AD9838. If the AD9838 is in a system where multiple devices
require AGND to DGND connections, the connection should
be made at one point only, a star ground point that should be
established as close as possible to the AD9838.
Avoid running digital lines under the device; these lines couple
noise onto the die. The analog ground plane should be allowed
to run under the AD9838 to avoid noise coupling. The power
supply lines to the AD9838 should use as large a track as possible
to provide low impedance paths and reduce the effects of glitches
on the power supply line. Fast switching signals, such as clocks,
should be shielded with digital ground to avoid radiating noise
to other sections of the board.
Avoid crossover of digital and analog signals. Traces on opposite
sides of the board should run at right angles to each other to
reduce the effects of feedthrough through the board. A micro-
strip technique is by far the best but is not always possible with
a double-sided board. In this technique, the component side of
the board is dedicated to ground planes and signals are placed
on the other side.
Good decoupling is important. The analog and digital supplies
to the AD9838 are independent and separately pinned out to
minimize coupling between the analog and digital sections of the
device. All analog and digital supplies should be decoupled to
AGND and DGND, respectively, with 0.1 μF ceramic capacitors
in parallel with 10 μF tantalum capacitors. To achieve the best
performance from the decoupling capacitors, they should be
placed as close as possible to the device, ideally right up against
the device.
In systems where a common supply is used to drive both the
AVDD and DVDD pins of the AD9838, it is recommended that
the system’s AVDD supply be used. This supply should have the
recommended analog supply decoupling between the AVDD
pin of the AD9838 and AGND, as well as the recommended
digital supply decoupling capacitors between the DVDD pin
and DGND.
Proper operation of the comparator requires good layout strategy.
The layout must minimize the parasitic capacitance between VIN
and the SIGN BIT OUT pin by using a ground plane to add
isolation. For example, in a multilayered board, the VIN signal
can be connected to the top layer, and the SIGN BIT OUT pin
can be connected to the bottom layer. In this way, isolation is
provided by the power and ground planes between VIN and the
SIGN BIT OUT pin.
INTERFACING TO MICROPROCESSORS
The AD9838 has a standard serial interface that allows the part to
interface directly with several microprocessors. The device uses
an external serial clock to write the data or control information
into the device. The serial clock can have a frequency of 40 MHz
maximum. The serial clock can be continuous, or it can idle high
or low between write operations. When data or control informa-
tion is written to the AD9838, FSYNC is taken low and is held
low until the 16 bits of data are written into the AD9838. The
FSYNC signal frames the 16 bits of information that are loaded
into the AD9838.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9838ACPZ-RL | IC DDS 16MHZ LOW PWR 20LFCSP |
| AD9837BCPZ-RL | IC WAVEFORM GEN PROG 10LFCSP |
| VE-2WM-IY-F2 | CONVERTER MOD DC/DC 10V 50W |
| AD9837ACPZ-RL | IC WAVEFORM GEN PROG 10LFCSP |
| VE-2W3-IY-F4 | CONVERTER MOD DC/DC 24V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9838BCPZ-RL | 功能描述:IC DDS 16MHZ LOW PWR 20LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD9838BCPZ-RL7 | 功能描述:IC DDS 16MHZ LP 20LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD9840 | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete 10-Bit 40 MSPS CCD Signal Processor |
| AD9840A | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete 10-Bit 40 MSPS CCD Signal Processor |
| AD9840AJST | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 48-Pin LQFP 制造商:Analog Devices 功能描述:AFE VID 1ADC 10-BIT 3.3V 48LQFP - Bulk |
发布紧急采购，3分钟左右您将得到回复。