- 您现在的位置：买卖IC网 > PDF目录11767 > AD9882AKSTZ-100 (Analog Devices Inc)IC INTERFACE/DVI 100MHZ 100LQFP PDF资料下载
参数资料
| 型号： | AD9882AKSTZ-100 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/40页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE/DVI 100MHZ 100LQFP |
| 标准包装： | 1 |
| 应用： | 视频 |
| 接口： | 模拟，DVI |
| 电源电压： | 3.15 V ~ 3.45 V |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
AD9882A
Rev. 0 | Page 36 of 40
PCB LAYOUT RECOMMENDATIONS
The AD9882A is a high precision, high speed analog device. To
derive the maximum performance from the part, it is important
to have a well laid out board. The following is a guide for
designing a board using the AD9882A.
ANALOG INTERFACE INPUTS
Using the following layout techniques on the graphics inputs is
extremely important.
Minimize the trace length running into the graphics inputs.
This is accomplished by placing the AD9882A as close as
possible to the graphics VGA connector. Long input trace
lengths are undesirable because they will pick up more noise
from the board and other external sources.
Place the 75 termination resistors (see Figure 9) as close to
the AD9882A chip as possible. Any additional trace length
between the termination resistors and the input of the
AD9882A increases the magnitude of reflections, which
corrupts the graphics signal.
Use 75 matched impedance traces. Trace impedances other
than 75 also increase the chance of reflections.
The AD9882A has a very high input bandwidth (300 MHz).
While this is desirable for acquiring a high resolution PC
graphics signal with fast edges, it means that it captures any
high frequency noise present. Therefore, it is important to
reduce the amount of noise that gets coupled to the inputs.
Avoid running any digital traces near the analog inputs.
Due to the high bandwidth of the AD9882A, sometimes low-
pass filtering the analog inputs can help to reduce noise. (For
many applications, filtering is unnecessary.) Experiments have
shown that placing a series ferrite bead prior to the 75
termination resistor is helpful in filtering out excess noise.
Specifically, the part used was the #2508051217Z0 from Fair-
Rite, but different applications may work best with different
bead values. Alternatively, placing a 100 to 120 resistor
between the 75 termination resistor and the input coupling
capacitor can also be beneficial.
DIGITAL INTERFACE INPUTS
Many of the same techniques that are recommended for the
analog interface inputs should also be used for the digital
interface inputs. It is important to minimize trace lengths, then
make the input trace impedances match the input termination
(typically 50 ). Each differential input pair (RX0+, RX0–, RXC+,
RXC–, and so on) should be routed together using 50 strip line
routing techniques and should be kept as short as possible. No
other components, such as clamping diodes, should be placed
on these inputs. Every effort should be made to route these
signals on a single layer (component layer) with no vias.
POWER SUPPLY BYPASSING
Bypassing each power supply pin with a 0.1 F capacitor is
recommended. The exception is when two or more supply pins
are adjacent to each other. For these groupings of powers/
grounds, it is necessary to have one bypass capacitor. The
fundamental idea is to have a bypass capacitor within about 0.5
cm of each power pin. Also, avoid placing the capacitor on the
side of the PC board opposite the AD9882A, as that interposes
resistive vias in the path.
The bypass capacitors should be physically located between the
power plane and the power pin. Current should flow from the
power plane ->to the capacitor ->to the power pin. Do not
make the power connection between the capacitor and the
power pin. Placing a via underneath the capacitor pads, down
to the power plane, is generally the best approach.
It is particularly important to maintain low noise and good
stability of PVD (the clock generator supply). Abrupt changes in
PVD can result in similarly abrupt changes in sampling clock
phase and frequency. This can be avoided by careful attention to
regulation, filtering, and bypassing. It is highly desirable to
provide separate regulated supplies for each of the analog
circuitry groups (VD and PVD).
Some graphic controllers use levels of power when active
(during active picture time) that are substantially different from
those used when they are idle (during horizontal and vertical
sync periods). This can result in a measurable change in the
voltage supplied to the analog supply regulator, which can in
turn produce changes in the regulated analog supply voltage.
This can be mitigated by regulating the analog supply, or at least
PVD, from a different, cleaner, power source (for example, from
a 12 V supply).
Using a single ground plane for the entire board is also recom-
mended. Experience has repeatedly shown that the noise
performance is the same or better with a single ground plane.
Using multiple ground planes can be detrimental, because each
separate ground plane is smaller than one common ground
plane, and can result in long ground loops.
In some cases, using separate ground planes is unavoidable.
When they must be used, it is recommended that at least a
single ground plane be placed under the AD9882A. The
location of the split should be at the receiver of the digital
outputs. In this case, it is even more important to place
components wisely, because the current loops are much longer
(current takes the path of least resistance). The following is an
example of a current loop: power plane -> AD9882A -> digital
output trace -> digital data receiver -> digital ground plane ->
analog ground plane.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9882KSTZ-100 | IC INTERFACE/DVI 100MHZ 100LQFP |
| MS27473E16B55PA | CONN PLUG 55POS STRAIGHT W/PINS |
| LTC4305IGN#TR | IC BUFFER BUS 2WR ADDRESS 16SSOP |
| VI-B43-IW-F2 | CONVERTER MOD DC/DC 24V 100W |
| AD9983AKCPZ-170 | IC INTRFACE 8BIT 170MSPS 64LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9882AKSTZ-140 | 功能描述:IC INTERFACE/DVI 100MHZ 100LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| AD9882KS-140 | 制造商:Analog Devices 功能描述:LOW COST DUAL INTERFACE - Bulk |
| AD9882KST-100 | 制造商:Rochester Electronics LLC 功能描述:LOW COST DUAL INTERFACE - Bulk |
| AD9882KST-140 | 制造商:Analog Devices 功能描述:Interface for Flat Panel Display 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:LOW COST DUAL INTERFACE - Bulk 制造商:Analog Devices 功能描述:IC DUAL INTERFACE |
| AD9882KSTZ-100 | 功能描述:IC INTERFACE/DVI 100MHZ 100LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。