- 您现在的位置：买卖IC网 > PDF目录10679 > ADCMP563BCPZ-R2 (Analog Devices Inc)IC COMPARATOR ECL DUAL 16LFCSP PDF资料下载
参数资料
| 型号： | ADCMP563BCPZ-R2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC COMPARATOR ECL DUAL 16LFCSP |
| 标准包装： | 250 |
| 类型： | 带锁销 |
| 元件数： | 2 |
| 输出类型： | 补充型，差分，ECL，开路发射极 |
| 电压 - 电源，单路/双路(±)： | ±4.75 V ~ 5.25 V |
| 电流 - 静态（最大值）： | 5mA |
| 磁滞： | ±1mV |
| 封装/外壳： | 16-VFQFN 裸露焊盘，CSP |
| 安装类型： | 表面贴装 |
| 包装： | 带卷 (TR) |
ADCMP563/ADCMP564
Rev. C | Page 12 of 16
Propagation delay dispersion is important in critical timing
applications such as ATE, bench instruments, and nuclear
instrumentation. Overdrive dispersion is defined as the varia-
tion in propagation delay as the input overdrive conditions are
changed (Figure 21). For the ADCMP563/ADCMP564, over-
drive dispersion is typically 75 ps as the overdrive is changed
from 100 mV to 1.5 V. This specification applies for both
positive and negative overdrive because the ADCMP563 and
the ADCMP564 have equal delays for positive and negative
going inputs.
Q OUTPUT
INPUT VOLTAGE
1.5V OVERDRIVE
20mV OVERDRIVE
DISPERSION
VREF ± VOS
04
65
0-
0
-0
04
Figure 21. Propagation Delay Dispersion
COMPARATOR HYSTERESIS
The addition of hysteresis to a comparator is often useful in a
noisy environment, or where it is not desirable for the compar-
ator to toggle between states when the input signal is at the
switching threshold. The transfer function for a comparator
with hysteresis is shown in Figure 22. If the input voltage
approaches the threshold from the negative direction, the
comparator switches from 0 to 1 when the input crosses +VH/2.
The new switching threshold becomes VH/2. The comparator
remains in a 1 state until the threshold VH/2 is crossed while
coming from the positive direction. In this manner, noise
centered on 0 V input does not cause the comparator to switch
states unless it exceeds the region bounded by ±VH/2.
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to the
input. A limitation of this approach is that the amount of
hysteresis varies with the output logic levels, resulting in
hysteresis that can be load dependent and is not symmetrical
about the threshold. The external feedback network can also
introduce significant parasitics, which reduce high speed
performance and can induce oscillation in some cases.
In the ADCMP564, hysteresis is generated through the
programmable hysteresis pin. A resistor from the HYS pin to
GND creates a current into the part that is used to generate
hysteresis. Hysteresis generated in this manner is independent
of output swing and is symmetrical around the trip point. The
hysteresis vs. resistance curve is shown in Figure 23.
A current may be sourced into the HYS pin. The pin is biased
approximately 1 V below AGND and has a 3 kΩ series
resistance. The relationship between the current applied to the
HYS pin and the resulting hysteresis is shown in Figure 19.
OUTPUT
INPUT
0
1
0V
–VH
2
+VH
2
04650-0-005
Figure 22. Comparator Hysteresis Transfer Function
160
140
120
100
80
60
40
20
0
50
0
10
20
30
40
04650-0-021
RHYS (kΩ)
PR
OGR
A
M
ED
H
YSTER
ESIS
(
m
V)
Figure 23. Comparator Hysteresis vs. RHYS
MINIMUM INPUT SLEW RATE REQUIREMENT
As for all high speed comparators, a minimum slew rate must
be met to ensure that the device does not oscillate as the input
crosses the threshold. This oscillation is due in part to the high
input bandwidth of the comparator and the parasitics of the
package. ADI recommends a slew rate of 1 V/μs or faster to
ensure a clean output transition. If slew rates less than 1 V/μs
are used, hysteresis can be added to prevent the oscillation.
相关PDF资料 |
PDF描述 |
|---|---|
| ISL4221EIRZ | IC TXRX 1TX/1RX 3V RS-232 16-QFN |
| LT685CN | IC COMP HI-SPD ECL OUTPUT 16-DIP |
| LTC2499IUHF#PBF | IC ADC 24BIT DELTA SIG 38-QFN |
| ISL41334IRZ-T | TRANSISTOR ESD SGL/DUAL 40-QFN |
| LT1721IS | IC COMP R-RINOUT QUAD 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADCMP563BCPZ-RL7 | 功能描述:校验器 IC Dual High Speed ECL Comparator RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| ADCMP563BCPZ-WP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADCMP563BRQ | 功能描述:IC COMPARATOR ECL DUAL 16QSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:通用 元件数:1 输出类型:CMOS，推挽式，满摆幅，TTL 电压 - 电源，单路/双路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 电压 - 输入偏移（最小值）:5mV @ 5.5V 电流 - 输入偏压（最小值）:1pA @ 5.5V 电流 - 输出（标准）:- 电流 - 静态（最大值）:24µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:450ns 磁滞:±3mV 工作温度:-40°C ~ 85°C 封装/外壳:6-WFBGA，CSPBGA 安装类型:表面贴装 包装:管件 其它名称:Q3554586 |
| ADCMP563BRQZ | 功能描述:IC COMPARATOR ECL DUAL 16QSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:带电压基准 元件数:4 输出类型:开路漏极 电压 - 电源，单路/双路(±):2.5 V ~ 11 V，±1.25 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:- 磁滞:- 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 安装类型:表面贴装 包装:管件 产品目录页面:1386 (CN2011-ZH PDF) |
| ADCMP564 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual High Speed ECL Comparators |
发布紧急采购，3分钟左右您将得到回复。