参数资料
型号: ADE7755ARSZ
厂商: Analog Devices Inc
文件页数: 14/20页
文件大小: 0K
描述: IC ENERGY METERING 1PHASE 24SSOP
标准包装: 59
输入阻抗: 390 千欧
测量误差: 0.1%
电压 - 高输入/输出: 2.4V
电压 - 低输入/输出: 0.8V
电流 - 电源: 3mA
电源电压: 4.75 V ~ 5.25 V
测量仪表类型: 单相
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-SSOP(0.209",5.30mm 宽)
供应商设备封装: 24-SSOP
包装: 管件
配用: EVAL-ADE7755ZEB-ND - BOARD EVALUATION FOR AD7755
ADE7755
Channel 2 (Voltage Channel)
PT
Rf
V2P
The output of the line voltage transducer is connected to the
ADE7755 at this analog input. Channel 2 is a fully differential
voltage input. The maximum peak differential signal on Channel 2
is ±660 mV. Figure 25 illustrates the maximum signal levels that
can be connected to Channel 2 of the ADE7755.
PHASE NEUTRAL
±660mV
AGND
Rf
Cf
Cf
V2N
V2
Ra 1
Cf
+660mV
V CM
DIFFERENTIAL INPUT
±660mV MAX PEAK
V2
V2P
V2N
Rb 1
VR 1
±660mV
Rf
V2P
V2N
COMMON-MODE
±100mV MAX
V CM
PHASE NEUTRAL
1 Ra >> Rb + VR
Rb + VR = Rf
Cf
–660mV
AGND
Figure 27. Typical Connections for Channel 2
Figure 25. Maximum Signal Levels, Channel 2
Channel 2 must be driven from a common-mode voltage, that
is, the differential voltage signal on the input must be referenced
to a common mode (usually AGND). The analog inputs of the
ADE7755 can be driven with common-mode voltages of up to
100 mV with respect to AGND. However, best results are achieved
using a common mode equal to AGND.
TYPICAL CONNECTION DIAGRAMS
Figure 26 shows a typical connection diagram for Channel 1. A
current transformer (CT) is the current transducer selected for
this example. Note that the common-mode voltage for Channel 1
is AGND and is derived by center-tapping the burden resistor to
AGND. This provides the complementary analog input signals for
V1P and V1N. The CT turns ratio and burden resistor Rb are
selected to give a peak differential voltage of ±470 mV/gain at
maximum load.
POWER SUPPLY MONITOR
The ADE7755 contains an on-chip power supply monitor. The
analog supply (AV DD ) is continuously monitored by the ADE7755.
If the supply is less than 4 V ± 5%, the ADE7755 resets. This is
useful to ensure correct device startup at power-up and power-
down. The power supply monitor has built-in hysteresis and
filtering. These features give a high degree of immunity to false
triggering due to noisy supplies.
In Figure 28, the trigger level is nominally set at 4 V. The
tolerance on this trigger level is about ±5%. The power supply
and decoupling for the part should be such that the ripple at
AV DD does not exceed 5 V ± 5%, as specified for normal
operation.
AV DD
5V
4V
CT
Rf
V1P
IP
AGND
Rb
±470mV
GAIN
Rf
Cf
Cf
V1N
0V
TIME
PHASE NEUTRAL
Figure 26. Typical Connection for Channel 1
INTERNAL
RESET
RESET
ACTIVE
RESET
Figure 27 shows two typical connections for Channel 2. The first
option uses a potential transformer (PT) to provide complete
isolation from the power line. In the second option, the ADE7755
is biased around the neutral wire, and a resistor divider provides
a voltage signal that is proportional to the line voltage. Adjusting
the ratio of Ra, Rb, and VR is also a convenient way of carrying
out a gain calibration on the meter.
Rev. A | Page 14 of 20
Figure 28. On-Chip Power Supply Monitor
相关PDF资料
PDF描述
ADE7757ARNZRL IC ENERGY METERING 1PHASE 16SOIC
ADE7758ARWZRL IC ENERGY METERING 3PHASE 24SOIC
ADE7761AARSZ-RL IC ENERGY METERING 1PHASE 20SSOP
ADE7761BARSZ-RL IC ENERGY METERING 1PHASE 20SSOP
ADE7768ARZ-RL IC ENERGY METERING 1PHASE 16SOIC
相关代理商/技术参数
参数描述
ADE7755ARSZ1 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Pulse Output
ADE7755ARSZRL 功能描述:IC ENERGY METERING 1PHASE 24SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7756 制造商:AD 制造商全称:Analog Devices 功能描述:Active Energy Metering IC with Serial Interface
ADE7756AN 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin PDIP
ADE7756AN-REF 制造商:AD 制造商全称:Analog Devices 功能描述:Active Energy Metering IC with Serial Interface