- 您现在的位置：买卖IC网 > PDF目录20640 > ADE7759ARSZ (Analog Devices Inc)IC ENERGY METERING 1PHASE 20SSOP PDF资料下载
参数资料
| 型号： | ADE7759ARSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 23/36页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 20SSOP |
| 标准包装： | 66 |
| 输入阻抗： | 390 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 3mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
| 配用： | EVAL-ADE7759EBZ-ND - BOARD EVALUATION FOR ADE7759 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ADE7759
load conditions. This output frequency can provide a simple,
single-wire, optically isolated interface to external calibration
equipment. Figure 38 illustrates the energy-to-frequency con-
version in the ADE7759.
The energy-to-frequency conversion is accomplished by accu-
mulating the active power signal in a 24-bit register. An output
pulse is generated when there is a zero to one transition on the
MSB (most significant bit) of the register. Under steady load con-
ditions the output frequency is proportional to the active power.
The output frequency at CF, with full-scale ac signals on
Channel 1 and Channel 2 and CFDEN = 000h, CFNUM = 000h,
and APGAIN = 000h, is approximately 5.593 kHz. This can be
calculated as follows:
output. Therefore, the content of CFDEN should always be set
no less than that of the CFNUM register, i.e., the maximum
output frequency from CF pin will never exceed that of the ETF
output. The power-up default value for CFDEN is 3Fh and
CFNUM is 0h.
The output frequency will have a slight ripple at a frequency
equal to twice the line frequency. This is due to imperfect filter-
ing of the instantaneous power signal to generate the active
power signal—see Active Power Calculation section. Equation 3
gives an expression for the instantaneous power signal. This is
filtered by LPF2, which has a magnitude response given by
Equation 10:
With the active power gain register set to 000h, the average
value of the instantaneous power signal (output of LPF2) is
H ( f ) =
1
1 + f / 8 . 9 Hz
(10)
CCCDh or 52,429 decimal. An output frequency is generated
on CF when the MSB in the energy-to-frequency register (24 bits)
The active power signal (output of LPF2) can be rewritten as:
? cos ( 4 π f l t )
p ( t ) = VI ? ?
toggles, i.e., when the register accumulates 2 23 . This means the
register is updated 2 23 /CCCDh times (or 159.999 times). Since
the update rate is 4/CLKIN or 1.1175 μ s, the time between
MSB toggles (CF pulses) is given as:
? VI ?
? 1 + 2 f l / 8 . 9 Hz ?
(11)
ETF Output ( Hz ) =
? sin ( 4 π f l t )
? VI ?
? ? 4 π f l ( 1 + 2 f l / 8 . 9 Hz ) ? ?
159 . 999 · 1 . 1175 m s = 1 . 78799 · 10 – 4 s ( 5592 . 86 Hz )
Equation 8 gives an expression for the output frequency at the
Energy-to-Frequency (ETF) output with the contents of CFDEN
and CFNUM registers are both zero.
Average LPF 2 Output × CLKIN
(8)
2 25
This output frequency is easily scaled by a pair of calibration
frequency divider registers (CFDEN[11:0] and CFNUM[11:0]).
These frequency scaling registers are 12-bit registers that can
scale the output frequency by 1 to 2 12 . The output frequency is
given by the expression below:
where f l is the line frequency (e.g., 60 Hz).
From Equation 6:
E ( t ) = VIt ? ? (12)
From Equation 12 it can be seen that there is a small ripple in
the energy calculation due to a sin(2 ω t) component. This is
shown in Figure 39. The active energy calculation is shown by
the dashed straight line and is equal to V × I × t. The sinusoidal
ripple in the active energy calculation is also shown. Since the
average value of a sinusoid is zero, this ripple will not contribute
to the energy calculation over time. However, the ripple can be
CF ( Hz ) = ETF Output ( Hz ) ×
CFNUM [11: 0 ] + 1
CFDEN [ 11 : 0 ] + 1
(9)
observed in the frequency output, especially at higher output
frequencies. The ripple will get larger as a percentage of the
frequency at larger loads and higher output frequencies. The rea-
For example, if the CF output frequency is 5.59286 kHz while
the contents of CFNUM and CFDEN are zero, the CF output
frequency can be set to 25 Hz by writing 8 BDh (2237 in deci-
mal) to the CFDEN register and 00Ah (10 in decimal) to the
CFNUM register. Note that the CFNUM and CFDEN regis-
ters are meant only to scale down the frequency from the ETF
son is that at higher output frequencies the integration or averaging
time in the energy-to-frequency conversion process is shorter. As
a consequence, some of the sinusoidal ripple is observable in the
frequency output. Choosing a lower output frequency at CF for
calibration can significantly reduce the ripple. Also, averaging the
output frequency by using a longer gate time for the counter will
achieve the same results.
15
APOS [15:0]
0
SIGN
2 6
2 5
2 4
2 3
2 2
2 1
2 0
2 –1 2 –2 2 –3 2 –4 2 –5 2 –6 2 –7 2 –8
20
LPF2
+
+
23
WAVEFORM [23:0]
0
ACTIVE POWER OFFSET
CALIBRATION
ENERGY-TO-FREQUENCY
ACTIVE POWER
23
0
+
SIGNAL – P
11
11
CFNUM [11:0]
CFDEN [11:0]
0
0
MSB
TRANSITION
+
CF
Figure 38. Energy-to-Frequency Conversion
REV. A
–23 –
相关PDF资料 |
PDF描述 |
|---|---|
| RMM40DTAD-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| EBC10DRTS-S13 | CONN EDGECARD 20POS .100 EXTEND |
| ADE7763ARSZ | IC ENERGY METERING 1PHASE 20SSOP |
| ISL6605IRZ | IC MOSFET DRVR SYNC BUCK 8-QFN |
| CS5463-ISZ | IC ENERGY METERING 1PHASE 24SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7759ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7760 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
| ADE7760ARS | 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP 制造商:Analog Devices 功能描述:ENERGY METER IC W/ ONCHIP FAULT & OSCIL. - Rail/Tube |
| ADE7760ARSRL | 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP T/R 制造商:Analog Devices 功能描述:ENERGY METER IC W/ONCHIP FAULT & OSCIL. - Tape and Reel |
| ADE7761 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
发布紧急采购，3分钟左右您将得到回复。