- 您现在的位置：买卖IC网 > PDF目录223307 > ADE7878ACPZ (ANALOG DEVICES INC) Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind PDF资料下载
参数资料
| 型号： | ADE7878ACPZ |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC40 |
| 封装： | 6 X 6 MM, ROHS COMPLIANT, MO-220WJJD, LFCSP-40 |
| 文件页数： | 27/96页 |
| 文件大小： | 1096K |
| 代理商： | ADE7878ACPZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页
ADE7854/ADE7858/ADE7868/ADE7878
Rev. E | Page 33 of 96
determined by their negative-to-positive transitions. The regular
succession of these zero-crossing events is Phase A followed by
Phase B followed by Phase C (see Figure 44). If the sequence of
zero-crossing events is, instead, Phase A followed by Phase C
followed by Phase B, then Bit 19 (SEQERR) in the STATUS1
register is set.
If Bit 19 (SEQERR) in the MASK1 register is set to 1 and a
phase sequence error event is triggered, the IRQ1 interrupt pin
is driven low. The status bit is cleared and the IRQ1 pin is set
high by writing to the STATUS1 register with the Status Bit 19
(SEQERR) set to 1.
The phase sequence error detection circuit is functional only
when the ADE78xx is connected in a 3-phase, 4-wire, three voltage
sensors configuration (Bits[5:4], CONSEL[1:0] in the ACCMODE
register, set to 00). In all other configurations, only two voltage
sensors are used; therefore, it is not recommended to use the
detection circuit. In these cases, use the time intervals between
phase voltages to analyze the phase sequence (see the Time
Interval Between Phases section for details).
Figure 43 presents the case in which Phase A voltage is not
followed by Phase B voltage but by Phase C voltage. Every time
a negative-to-positive zero crossing occurs, Bit 19 (SEQERR) in
the STATUS1 register is set to 1 because such zero crossings on
Phase C, Phase B, or Phase A cannot come after zero crossings
from Phase A, Phase C, or respectively, Phase B zero crossings.
ZX B
ZX C
PHASE C
PHASE B
PHASE A
A, B, C PHASE
VOLTAGES AFTER
LPF1
BIT 19 (SEQERR) IN
STATUS1 REGISTER
IRQ1
ZX A
STATUS1[19] SET TO 1
STATUS1[19] CANCELLED
BY A WRITE TO THE
STATUS1 REGISTER WITH
SEQERR BIT SET
08
51
0-
02
9
Figure 43. SEQERR Bit Set to 1 When Phase A Voltage Is Followed by
Phase C Voltage
Once a phase sequence error has been detected, the time
measurement between various phase voltages (see the Time
Interval Between Phases section) can help to identify which
phase voltage should be considered with another phase current
in the computational datapath. Bits[9:8] (VTOIA[1:0]), Bits[11:10]
(VTOIB[1:0]), and Bits[13:12] (VTOIC[1:0]) in the CONFIG
register can be used to direct one phase voltage to the datapath
of another phase. See the Changing Phase Voltage Datapath
section for details.
Time Interval Between Phases
The ADE7854/ADE7858/ADE7868/ADE7878 have the capa-
bility to measure the time delay between phase voltages, between
phase currents, or between voltages and currents of the same
phase. The negative-to-positive transitions identified by the zero-
crossing detection circuit are used as start and stop measuring
points. Only one set of such measurements is available at one time,
based on Bits[10:9] (ANGLESEL[1:0]) in the COMPMODE
register.
ZX C
ZX B
PHASE B
PHASE C
PHASE A
ZX A
0
85
10
-0
30
Figure 44. Regular Succession of Phase A, Phase B, and Phase C
When the ANGLESEL[1:0] bits are set to 00, the default value,
the delays between voltages and currents on the same phase are
measured. The delay between Phase A voltage and Phase A
current is stored in the 16-bit unsigned ANGLE0 register (see
Figure 45 for details). In a similar way, the delays between voltages
and currents on Phase B and Phase C are stored in the ANGLE1
and ANGLE2 registers, respectively.
PHASE A
CURRENT
ANGLE0
PHASE A
VOLTAGE
08
51
0-
03
1
Figure 45. Delay Between Phase A Voltage and Phase A Current Is
Stored in the ANGLE0 Register
When the ANGLESEL[1:0] bits are set to 01, the delays between
phase voltages are measured. The delay between Phase A voltage
and Phase C voltage is stored into the ANGLE0 register. The
delay between Phase B voltage and Phase C voltage is stored in
the ANGLE1 register, and the delay between Phase A voltage
and Phase B voltage is stored in the ANGLE2 register (see
Figure 46 for details).
When the ANGLESEL[1:0] bits are set to 10, the delays between
phase currents are measured. Similar to delays between phase
voltages, the delay between Phase A and Phase C currents is stored
into the ANGLE0 register, the delay between Phase B and Phase C
currents is stored in the ANGLE1 register, and the delay between
Phase A and Phase B currents is stored into the ANGLE2
register (see Figure 46 for details).
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7878ACPZ-RL | Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind |
| ADG529FTQ | 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, CDIP18 |
| ADJ24006 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.042A (COIL), 6VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24012 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.021A (COIL), 12VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24024 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.01A (COIL), 24VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7878ACPZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION ENERGY METERING LFCSP40 |
| ADE7878ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7878XCPZ | 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk |
| ADE7880 | 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE |
| ADE7880ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
发布紧急采购，3分钟左右您将得到回复。