收藏本站
参数资料
型号： ADE7878ACPZ
厂商： ANALOG DEVICES INC
元件分类： 模拟信号调理
英文描述： Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind
中文描述： SPECIALTY ANALOG CIRCUIT, QCC40
封装： 6 X 6 MM, ROHS COMPLIANT, MO-220WJJD, LFCSP-40
文件页数： 49/96页
文件大小： 1096K
代理商： ADE7878ACPZ
ADE7854/ADE7858/ADE7868/ADE7878
Rev. E | Page 53 of 96
Integration Time Under A Steady Load
The discrete time sample period (T) for the accumulation register
is 125 μs (8 kHz frequency). With full-scale pure sinusoidal signals
on the analog inputs and a 90° phase difference between the vol-
tage and the current signal (the largest possible reactive power),
the average word value representing the reactive power is PMAX =
33,516,139 = 0x1FF6A6B. If the VARTHR threshold is set at the
PMAX level, this means the DSP generates a pulse that is added
at the var-hour registers every 125 μs.
The maximum value that can be stored in the var-hour
accumulation register before it overflows is 231 1 or
0x7FFFFFFF. The integration time is calculated as
Time = 0x7FFF,FFFF × 125 μs = 74 hr 33 min 55 sec
(38)
Energy Accumulation Modes
The reactive power accumulated in each var-hour accumulation
32-bit register (AVARHR, BVARHR, CVARHR, AFVARHR,
BFVARHR, and CFVARHR) depends on the configuration of
Bits[5:4] (CONSEL[1:0]) in the ACCMODE register, in correlation
with the watt-hour registers. The different configurations are
described in Table 19. Note that IA’/IB’/IC’ are the phase-shifted
current waveforms.
Table 19. Inputs to Var-Hour Accumulation Registers
CONSEL[1:0]
AVARHR,
AFVARHR
BVARHR,
BFVARHR
CVARHR,
CFVARHR
00
VA × IA’
VB × IB’
VC × IC’
01
VA × IA’
0
VC × IC’
10
VA × IA’
VB × IB’
VC × IC’
VB = VA VC
11
VA × IA’
VB × IB’
VC × IC’
VB = VA
Bits[3:2] (VARACC[1:0]) in the ACCMODE register determine
how CF frequency output can be a generated function of the total
active and fundamental powers. While the var-hour accumulation
registers accumulate the reactive power in a signed format, the
frequency output can be generated in either the signed mode or the
sign adjusted mode function of VARACC[1:0]. See the Energy-to-
Frequency Conversion section for details.
Line Cycle Reactive Energy Accumulation Mode
As mentioned in the Line Cycle Active Energy Accumulation
Mode section, in line cycle energy accumulation mode, the
energy accumulation can be synchronized to the voltage
channel zero crossings so that reactive energy can be accu-
mulated over an integral number of half line cycles.
In this mode, the ADE7858/ADE7868/ADE7878 transfer the
reactive energy accumulated in the 32-bit internal accumulation
registers into the xVARHR or xFVARHR registers after an
integral number of line cycles, as shown in Figure 67. The
number of half line cycles is specified in the LINECYC register.
The line cycle reactive energy accumulation mode is activated by
setting Bit 1 (LVAR) in the LCYCMODE register. The total reactive
energy accumulated over an integer number of half line cycles
or zero crossings is available in the var-hour accumulation registers
after the number of zero crossings specified in the LINECYC reg-
ister is detected. When using the line cycle accumulation mode,
Bit 6 (RSTREAD) of the LCYCMODE register should be set to
Logic 0 because a read with the reset of var-hour registers is not
available in this mode.
ZERO-
CROSSING
DETECTION
(PHASE A)
ZERO-
CROSSING
DETECTION
(PHASE B)
CALIBRATION
CONTROL
ZERO-
CROSSING
DETECTION
(PHASE C)
LINECYC[15:0]
AVARHR[31:0]
ZXSEL[0] IN
LCYCMODE[7:0]
ZXSEL[1] IN
LCYCMODE[7:0]
ZXSEL[2] IN
LCYCMODE[7:0]
OUTPUT
FROM
TOTAL
REACTIVE
POWER
ALGORITHM
AVARGAIN
AVAROS
ACCUMULATOR
VARTHR[47:0]
32-BIT
REGISTER
08
51
0-
1
46
Figure 67. Line Cycle Reactive Energy Accumulation Mode
Phase A, Phase B, and Phase C zero crossings are, respectively,
included when counting the number of half line cycles by setting
Bits[5:3] (ZXSEL[x]) in the LCYCMODE register. Any combi-
nation of the zero crossings from all three phases can be used
for counting the zero crossing. Select only one phase at a time
for inclusion in the zero-crossings count during calibration.
For details on setting the LINECYC register and the Bit 5
(LENERGY) in the MASK0 interrupt mask register associated
with the line cycle accumulation mode, see the Line Cycle
Active Energy Accumulation Mode section.
相关PDF资料
PDF描述
ADE7878ACPZ-RL Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind
ADG529FTQ 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, CDIP18
ADJ24006 POWER/SIGNAL RELAY, SPST, LATCHED, 0.042A (COIL), 6VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT
ADJ24012 POWER/SIGNAL RELAY, SPST, LATCHED, 0.021A (COIL), 12VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT
ADJ24024 POWER/SIGNAL RELAY, SPST, LATCHED, 0.01A (COIL), 24VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT
相关代理商/技术参数
参数描述
ADE7878ACPZ 制造商:Analog Devices 功能描述:IC MULTIFUNCTION ENERGY METERING LFCSP40
ADE7878ACPZ-RL 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7878XCPZ 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk
ADE7880 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE
ADE7880ACPZ 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*