- 您现在的位置：买卖IC网 > PDF目录20428 > ADM00427 (Microchip Technology)BOARD EVALUATION MCP16323 PDF资料下载
参数资料
| 型号： | ADM00427 |
| 厂商： | Microchip Technology |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION MCP16323 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3V |
| 电流 - 输出： | 3A |
| 输入电压： | 6 ~ 18 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MCP16323 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MCP16323
4.2
Functional Description
L
V OUT
4.2.1
STEP-DOWN OR BUCK
CONVERTER
S 1
I L
The MCP16323 is a synchronous, step-down or buck
converter capable of stepping input voltages ranging
from 6V to 18V down to 0.9V to 5V.
V IN
S 2
C OUT
The integrated high-side switch is used to chop or
modulate the input voltage using a controlled duty cycle
for output voltage regulation. The integrated low-side
switch is used to freewheel current when the high-side
switch is turned off. High efficiency is achieved by using
low-resistance switches and low equivalent series
resistance (ESR), inductor and capacitors. When the
high-side switch is turned on, a DC voltage is applied to
the inductor (V IN – V OUT ), resulting in a positive linear
ramp of inductor current. When the high-side switch
turns off and the low-side switch turns on, the applied
inductor voltage is equal to –V OUT , resulting in a
negative linear ramp of inductor current. In order to
ensure there is no shoot through current, a dead time
I L
SW
V IN
I OUT
V OUT
where both switches are off is implemented between
the high-side switch turning off and the low-side switch
turning on, and the low-side switch turning off and the
high-side switch turning on.
For steady-state, continuous inductor current
operation, the positive inductor current ramp must
equal the negative current ramp in magnitude. While
I L
S 1 ON
S 2 ON
Continuous Inductor Current Mode
S 1 ON S 2
operating in steady state, the switch duty cycle must be
equal to the relationship of V OUT /V IN for constant
output voltage regulation, under the condition that the
inductor current is continuous, or never reaches zero.
For discontinuous inductor current operation, the
steady-state duty cycle will be less than V OUT /V IN to
maintain voltage regulation. When the inductor current
reaches zero, the low-side switch is turned off so that
current does not flow in the reverse direction, keeping
SW
V IN
Both
ON OFF
Discontinuous Inductor Current Mode
I OUT
the efficiency high. The average of the chopped input
voltage or SW node voltage is equal to the output
voltage, while the average inductor current is equal to
the output current.
FIGURE 4-2:
Converter.
Synchronous Step-Down
4.2.2
PEAK CURRENT MODE CONTROL
For Pulse-Width Modulation (PWM) duty cycles that
The MCP16323 integrates a Peak Current Mode
Control architecture, resulting in superior AC regulation
while minimizing the number of voltage loop
compensation components, and their size, for
integration. Peak Current Mode Control takes a small
portion of the inductor current, replicates it and
compares this replicated current sense signal with the
output of the integrated error voltage. In practice, the
inductor current and the internal switch current are
equal during the switch-on time. By adding this peak
current sense to the system control, the step-down
power train system can be approximated by a 1 st order
system rather than a 2 nd order system. This reduces
the system complexity and increases its dynamic
performance.
? 2011 Microchip Technology Inc.
exceed 50%, the control system can become bimodal,
where a wide pulse followed by a short pulse repeats
instead of the desired fixed pulse width. To prevent this
mode of operation, an internal compensating ramp is
summed into the current sense signal.
4.2.3 PULSE WIDTH MODULATION
(PWM)
The internal oscillator periodically starts the switching
period, which in the MCP16323’s case occurs every
1 μs or 1 MHz. With the high-side integrated
N-Channel MOSFET turned on, the inductor current
ramps up until the sum of the current sense and slope
compensation ramp exceeds the integrated error
amplifier output. Once this occurs, the high-side switch
DS22284A-page 17
相关PDF资料 |
PDF描述 |
|---|---|
| 17PY-Z053-99VS | MOTOR STEP UNI .9DEG 42MM 24V DL |
| ESA06DTMD | CONN EDGECARD 12POS R/A .125 SLD |
| T95Y686M004CSAL | CAP TANT 68UF 4V 20% 2910 |
| MKP1V240RLG | SIDAC BIDIR 0.9A 240V DO-41 |
| AT45DB081B-CNU-2.5 | IC FLASH 8MBIT 20MHZ 8CASON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM00433 | 功能描述:MCP16301 - DC/DC, Step Down 1, Non-Isolated Outputs Evaluation Board 制造商:microchip technology 系列:- 零件状态:有效 主要用途:DC/DC，步降 输出和类型:1，非隔离 功率 - 输出:- 电压 - 输出:5V 电流 - 输出:600mA 电压 - 输入:6 V ~ 30 V 稳压器拓扑:降压 频率 - 开关:- 板类型:完全填充 所含物品:板 使用的 IC/零件:MCP16301 标准包装:1 |
| ADM00434 | 制造商:Microchip Technology Inc 功能描述:MCP19035 300 KHZ SYNCHRONOUS BUCK CONTROLLER EVALUATION BOAR - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:BOARD EVAL FOR MCP19035 制造商:Microchip Technology Inc 功能描述:MCP19035 300 kHz Evaluation Board |
| ADM00435 | 功能描述:MCP1643 1, Non-Isolated Output LED Driver Evaluation Board 制造商:microchip technology 系列:- 零件状态:有效 电流 - 输出/通道:25mA，50mA，75mA，或 100mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:0.35 V ~ 2.5 V 所含物品:板 使用的 IC/零件:MCP1643 标准包装:1 |
| ADM00443 | 功能描述:MCP6421 1 - Single Channels per IC General Purpose Amplifier Evaluation Board 制造商:microchip technology 系列:- 零件状态:有效 每 IC 通道数:1 - 单 放大器类型:通用 输出类型:单端，满摆幅 压摆率:0.05 V/μs -3db 带宽:- 电流 - 输出/通道:22mA 工作温度:-40°C ~ 125°C 电流 - 电源（主 IC）:4.4μA 电压 - 电源，单/双（±）:1.8 V ~ 5.5 V，±0.9 V ~ 2.75 V 板类型:完全填充 所含物品:板 使用的 IC/零件:MCP6421 标准包装:1 |
| ADM00445 | 制造商:Microchip Technology Inc 功能描述:MCP19035 600KHZ EVALUATION BOARD - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:BOARD EVAL ANALOG MCP19035 制造商:Microchip Technology Inc 功能描述:MCP19035 600KHz Evaluation Board, DEVTOOL - Analog |
发布紧急采购，3分钟左右您将得到回复。