- 您现在的位置：买卖IC网 > PDF目录11749 > ADM1024ARUZ-REEL (ON Semiconductor)IC MONITOR SYS TEMP/VOLT 24TSSOP PDF资料下载
参数资料
| 型号： | ADM1024ARUZ-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/30页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SYS TEMP/VOLT 24TSSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi |
| 标准包装： | 2,500 |
| 应用： | PC，PDA |
| 接口： | 串行 |
| 电源电压： | 2.8 V ~ 5.5 V |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
| 其它名称： | ADM1024ARUZ-REEL-ND ADM1024ARUZ-REELOSTR |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
ADM1024
http://onsemi.com
17
voltage dividers and analog components, will provide best
performance but is not mandatory.
The power supply bypass, the parallel combination of
10
mF (electrolytic or tantalum) and 0.1 mF (ceramic) bypass
capacitors connected between Pin 9 and ground, should also
be located as close as possible to the ADM1024.
Fan Inputs
Pins 5 and 6 may be configured as analog inputs or fan
speed inputs by programming Bits 0 and 1 of the Channel
Mode Register. The power-on default for these bits is all
zeros, which makes Pins 5 and 6 fan inputs.
Signal conditioning in the ADM1024 accommodates the
slow rise and fall times typical of fan tachometer outputs.
The maximum input signal range is 0 to VCC. In the event
that these inputs are supplied from fan outputs that exceed
0 V to 6.5 V, either resistive attenuation of the fan signal or
diode clamping must be included to keep inputs within an
acceptable range.
tachometer outputs.
If the fan tachometer output has a resistive pullup to VCC,
it can be directly connected to the fan input, as shown in
Figure 25.
Figure 25. Fan with Tach Pullup to +VCC
160k
PULLUP
4.7k
TYP
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
W
If the fan output has a resistive pullup to 12 V (or other
voltage greater than 6.5 V), the fan output can be clamped
with a Zener diode, as shown in Figure 26. The Zener
voltage should be chosen so it is greater than VIH but less
than 6.5 V, allowing for the voltage tolerance of the Zener.
A value of between 3.0 V and 5.0 V is suitable.
Figure 26. Fan with Tach. Pullup to Voltage >6.5 V
(e.g., 12 V) Clamped with Zener Diode
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 y VCC.
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
ZD1*
ZENER
160k
PULLUP
4.7k
TYP
W
If the fan has a strong pullup (less than 1 k
W) to 12 V, or
a totem-pole output, then a series resistor can be added to
limit the Zener current, as shown in Figure 27. Alternatively,
a resistive attenuator may be used, as shown in Figure 28.
R1 and R2 should be chosen such that:
(eq. 7)
2.0 V t VPULLUP
R2
RPULLUP ) R1 ) R2
t
t 5.0 V
The fan inputs have an input resistance of nominally
160 k
W to ground, so this should be taken into account when
calculating resistor values.
With a pullup voltage of 12 V and pullup resistor less than
1 k
W, suitable values for R1 and R2 would be 100 kW and
47 k
W. This will give a high input voltage of 3.83 V.
Figure 27. Fan with Strong Tach Pullup to >VCC or
Totem Pole Output, Clamped with Zener and Resistor
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 y VCC
PULLUP
TOTEMPOLE
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
ZD1*
ZENER
160kW
TYP <1k OR
W
R1
10kW
Figure 28. Fan with Strong Tach Pullup to > VCC or
Totem Pole Output, Attenuated with R1/R2
*SEE TEXT.
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
R1*
R2*
160k
<1k W
W
Fan Speed Measurement
The fan counter does not count the fan tachometer output
pulses directly because the fan speed may be less than
1000 rpm and it would take several seconds to accumulate
a reasonably large and accurate count. Instead, the period of
the fan revolution is measured by gating an on-chip
22.5 kHz oscillator into the input of an 8-bit counter for two
periods of the fan tachometer output, as shown in Figure 29;
the accumulated count is actually proportional to the fan
tachometer period and inversely proportional to the fan
speed.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC18LF46K80-I/P | MCU PIC ECAN 64KB FLASH 40DIP |
| MS27468E13B22S | CONN RCPT 22POS JAM NUT W/SCKT |
| VE-B4F-IW-F1 | CONVERTER MOD DC/DC 72V 100W |
| PIC16LC620-04/SO | IC MCU OTP 512X14 COMP 18SOIC |
| VE-B4D-IX-F4 | CONVERTER MOD DC/DC 85V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| ADM1024EVB | 功能描述:BOARD EVAL FOR ADM1024 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1025 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
| ADM1025A | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
| ADM1025AARQ | 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
发布紧急采购，3分钟左右您将得到回复。