- 您现在的位置：买卖IC网 > PDF目录22035 > ADM1026JST-REEL (ON Semiconductor)IC CNTRL SYS REF/EEPROM 48LQFP PDF资料下载
参数资料
| 型号： | ADM1026JST-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 13/55页 |
| 文件大小： | 0K |
| 描述： | IC CNTRL SYS REF/EEPROM 48LQFP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 30/Sept/2009 |
| 标准包装： | 2,000 |
| 功能： | 硬件监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 100°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
ADM1026
SLAVE
ADDRESS
SMBus Protocols for RAM and EEPROM
The ADM1026 contains volatile registers (RAM) and
non-volatile EEPROM. RAM occupies Addresses 00h to
6Fh, while EEPROM occupies Addresses 8000h to 9FFFh.
Data can be written to and read from both RAM and
EEPROM as single data bytes and as block (sequential) read
or write operations of 32 data bytes, the maximum block size
allowed by the SMBus specification.
Data can only be written to unprogrammed EEPROM
locations. To write new data to a programmed location, it is
first necessary to erase it. EEPROM erasure cannot be done
at the byte level; the EEPROM is arranged as 128 pages of
64 bytes, and an entire page must be erased. Note that of
these 128 pages, only 124 pages are available to the user. The
last four pages are reserved for manufacturing purposes and
cannot be erased/rewritten.
The EEPROM has three RAM registers associated with it,
EEPROM Registers 1, 2, and 3 at Addresses 06h, 0Ch, and
13h. EEPROM Registers 1 and 2 are for factory use only.
EEPROM Register 3 sets up the EEPROM operating mode.
Setting Bit 0 of EEPROM Register 3 puts the EEPROM into
read mode. Setting Bit 1 puts it into programming mode.
Setting Bit 2 puts it into erase mode.
Only one of these bits must be set before the EEPROM
may be accessed. Setting no bits or more than one of them
causes the device to respond with No Acknowledge if an
EEPROM read, program, or erase operation is attempted.
It is important to distinguish between SMBus write
operations, such as sending an address or command, and
EEPROM programming operations. It is possible to write an
EEPROM address over the SMBus, whatever the state of
EEPROM Register 3. However, EEPROM Register 3 must
be correctly set before a subsequent EEPROM operation can
be performed. For example, when reading from the
EEPROM, Bit 0 of EEPROM Register 3 can be set, even
though SMBus write operations are required to set up the
EEPROM address for reading. Bit 3 of EEPROM Register 3
is used for EEPROM write protection. Setting this bit
prevents accidental programming or erasure of the
EEPROM. If an EEPROM write or erase operation is
attempted when this bit is set, the ADM1026 responds with
No Acknowledge. This bit is write-once and can only be
cleared by a power-on reset.
EEPROM Register 3 Bit 7 is used for clock extend.
Programming an EEPROM byte takes approximately
250 m s, which would limit the SMBus clock for repeated or
block write operations. Because EEPROM block read/write
access is slow, it is recommended that this clock extend bit
typically be set to 1. This allows the ADM1026 to pull SCL
low and extend the clock pulse when it cannot accept any
more data.
ADM1026 SMBus Operations
The SMBus specifications define several protocols for
different types of read and write operations. The ones used
S ? START
W ? WRITE
P ? STOP
A ? ACKNOWLEDGE
R ? READ
A ? NO ACKNOWLEDGE
ADM1026 Write Operations
Send Byte
In this operation, the master device sends a single
command byte to a slave device, as follows:
1. The master device asserts a start condition on the
SDA.
2. The master sends the 7-bit slave address followed
by the write bit (low).
3. The addressed slave device asserts an ACK on the
SDA.
4. The master sends a command code.
5. The slave asserts ACK on the SDA.
6. The master asserts a stop condition on the SDA
and the transaction ends.
In the ADM1026, the send byte protocol is used to write
a register address to RAM for a subsequent single ? byte read
from the same address or block read or write starting at that
address. This is illustrated in Figure 18.
1 2 3 4 5 6
RAM
S W A ADDRESS A P
(00h TO 6Fh)
Figure 18. Setting a RAM Address for Subsequent Read
If it is required to read data from the RAM immediately
after setting up the address, the master can assert a repeat
start condition immediately after the final ACK and carry
out a single byte read, block read, or block write operation
without asserting an intermediate stop condition.
Write Byte/Word
In this operation, the master device sends a command byte
and one or two data bytes to the slave device as follows:
1. The master device asserts a start condition on the
SDA.
2. The master sends the 7-bit slave address followed
by the write bit (low).
3. The addressed slave device asserts an ACK on the
SDA.
4. The master sends a command code.
5. The slave asserts an ACK on the SDA.
6. The master sends a data byte.
7. The slave asserts an ACK on the SDA.
8. The master sends a data byte (or may assert stop
here.)
9. The slave asserts an ACK on the SDA.
10. The master asserts a stop condition on the SDA to
end the transaction.
in the ADM1026 are discussed below. The following
abbreviations are used in the diagrams:
http://onsemi.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| AGLN020V2-CSG81 | IC FPGA 20K 1.2-1.5V CSP81 |
| ADM1026JST | IC CNTRL SYS REF/EEPROM 48LQFP |
| LQG15HSR22J02D | INDUCTOR 220NH 120MA 0402 |
| GCC10DCSN | CONN EDGECARD 20POS DIP .100 SLD |
| VJ1206Y122KBAAT4X | CAP CER 1200PF 50V 10% X7R 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解决方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解决方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安装温度传感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1026JSTZ-REEL7 | 制造商:Analog Devices 功能描述:IC SYSTEM MONITOR 制造商:ON Semiconductor 功能描述:IC SYSTEM MONITOR |
发布紧急采购，3分钟左右您将得到回复。