- 您现在的位置：买卖IC网 > PDF目录20033 > ADM1075-2ARUZ (Analog Devices Inc)IC CTRLR HOTSWAP -48V 28TSSOP PDF资料下载
参数资料
| 型号： | ADM1075-2ARUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/52页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTSWAP -48V 28TSSOP |
| 标准包装： | 50 |
| 类型： | 热交换控制器 |
| 应用： | -48V 远程电力系统，高可用性，电信/数据通信系统 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | -35 V ~ -80 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADM1075
Pin No.
Data Sheet
TSSOP
14
LFCSP
10
Mnemonic
SHDN
Description
Drive this pin low to shut down the gate. Internal weak pull-up to VIN.
This pin is also used to configure the desired retry scheme. See the Hot Swap Fault Retry section for
additional details.
15
16
11
12
RESTART
GPO1/ALERT1
/CONV
Falling Edge Triggered 10 sec Automatic Restart. The gate remains off for 10 seconds, and then
powers back up. Internal weak pull-up to VIN. This pin is also used to configure the desired retry
scheme. See the Hot Swap Fault Retry section for additional details.
General-Purpose Digital Output (GPO1).
Alert (ALERT1). This pin can be configured to generate an alert signal when one or more fault or
warning conditions have been detected.
Conversion (CONV). This pin can be used as an input signal to control when a power monitor ADC
sampling cycle begins.
This pin defaults to indicate FET health mode at power-up. There is no internal pull-up on this pin.
17
13
GPO2/ALERT2
General-Purpose Digital Output (GPO2).
Alert (ALERT2). This pin can be configured to generate an alert signal when one or more fault or
warning conditions have been detected.
This pin is also used to configure the desired retry scheme. See the Hot Swap Fault Retry section for
further details. This pin defaults to indicate a seven-attempt fail at power-up.
There is no internal pull-up on this pin.
18
19
20
21
22
23
24
25
14
15
16
17
18
19
20
21
SDAO
SDAI
SCL
PWRGD
ADC_AUX
SPLYGD
VEE
SENSE?
PMBus Serial Data Output. This is a split version of the SDA for easy use with optocouplers.
PMBus Serial Data Input. This is a split version of the SDA for easy use with optocouplers.
PMBus Clock Pin. Open-drain input requires an external resistive pull-up.
Power-Good Signal. This pin is used to indicate that the FET is no longer in the linear region and
capacitors are fully charged. See the PWRGD section for details on assert and deassert.
This pin is used to read back a voltage using the internal ADC.
This pin asserts low when the supply is within the UV and OV limits set by the UVx and OV pins.
Chip Ground Pin. Must connect to –VIN rail (lowest potential).
Negative Current Sense Input Pin. A sense resistor between the SENSE+ pin and the SENSE? pin sets
the analog current limit. The hot swap operation controls the external FET gate to maintain the
(V SENSE+ ? V SENSE? ) sense voltage. This pin also connects to the VEE node, but should be routed
separately.
26
22
SENSE+
Positive Current Sense Input Pin. A sense resistor between the SENSE+ pin and the SENSE? pin sets
the analog current limit. The hot swap operation controls the external FET gate to maintain the
(V SENSE+ ? V SENSE? ) sense voltage. This pin also connects to the FET source node.
27
23
GATE
Gate Output Pin. This pin is the gate drive of an external N-channel FET. It is driven by the FET drive
controller. The FET drive controller regulates to a maximum load current by regulating the GATE pin.
GATE is held low while the supply is out of the voltage range.
28
24
EPAD
VEE_G
EPAD
Chip Ground Pin. Must connect to –VIN rail (lowest potential). The PCB layout should configure this
pin as the gate pull-down return.
Exposed Pad. Solder the exposed pad to the board to improve thermal dissipation. The exposed pad
can be connected to VEE.
Rev. C | Page 12 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| M1MA174T1 | DIODE SW SS 200MA 100V SOT-323 |
| RCB105DHLD | CONN EDGECARD 210PS DIP .050 SLD |
| VE-24X-CX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| GRM1885C1H681JA01D | CAP CER 680PF 50V 5% NP0 0603 |
| ADM1275-2ARQZ | IC HOT SWAP CTRL PMBUS 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1075-2ARUZ-RL7 | 功能描述:IC HOTSWAP CTRLR -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1085 | 制造商:AD 制造商全称:Analog Devices 功能描述:Simple Sequencers in 6-Lead SC70 |
| ADM1085AKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:SIMPLE SEQUENCER OPEN DRAIN EN IC - Tape and Reel 制造商:Analog Devices 功能描述:IC VOLTAGE SEQUENCER |
| ADM1085AKS-U1 | 制造商:Analog Devices 功能描述:- Bulk |
| ADM1085AKSZ-REEL7 | 功能描述:IC SIMPLE SEQUENCER OD SC70-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Simple Sequencers® 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极，开路漏极 复位:高有效/低有效 复位超时:最小为 250 ms 电压 - 阀值:4.37V，4.62V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 产品目录页面:1337 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。