- 您现在的位置：买卖IC网 > PDF目录20033 > ADM1075-2ARUZ (Analog Devices Inc)IC CTRLR HOTSWAP -48V 28TSSOP PDF资料下载
参数资料
| 型号： | ADM1075-2ARUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/52页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTSWAP -48V 28TSSOP |
| 标准包装： | 50 |
| 类型： | 热交换控制器 |
| 应用： | -48V 远程电力系统，高可用性，电信/数据通信系统 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | -35 V ~ -80 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADM1075
GENERAL DESCRIPTION
The ADM1075 is a full feature, negative voltage, hot swap control-
ler with constant power foldback and high accuracy digital current
and voltage measurement that allows boards to be safely inserted
and removed from a live ?48 V backplane. The part provides
precise and robust current limiting and protection against both
transient and nontransient short circuits and overvoltage and
undervoltage conditions. The ADM1075 typically operates from
a negative voltage of ?35 V to ?80 V and, due to shunt regulation,
has excellent voltage transient immunity. The operating range of
the part is flexible due to the shunt regulator, and the part can be
powered directly by a 10 V rail to save shunt power dissipation
(see the Powering the ADM1075 section for more details).
A full-scale current limit of 25 mV or 50 mV can be selected by
choosing the appropriate model. The maximum current limit is
set by the combination of the sense resistor, R SENSE , and the input
voltage on the ISET pin, using external resistors. This allows fine
tuning of the trip voltage so that standard sense resistors can be
used. Inrush current is limited to this programmable value by
controlling the gate drive of an external N-channel FET. A built-
in soft start function allows control of the inrush current profile by
an external capacitor on the soft start (SS) pin.
An external capacitor on the TIMER pin determines the maxi-
mum allowed on-time for when the system is in current limit.
This is based on the safe operating area (SOA) limits of the
MOSFET. A constant power foldback scheme is used to control
the power dissipation in the MOSFET during power-up and
fault conditions. The ADM1075 regulates the current dynami-
cally to ensure that the power in the MOSFET is within SOA
limits as V DS changes. After the timer has expired, the device
shuts down the MOSFET. The level of this power, along with
the TIMER regulation time, can be set to ensure that the
MOSFET remains within the SOA limits.
The ADM1075 employs a limited consecutive retry scheme
when the LATCH pin is tied to the SHDN pin. In this mode,
if the load current reaches the limit, the FET gate is pulled low
after the timer expires and retries after a cooling period for
seven attempts only. If the fault remains, the device latches off,
and the MOSFET is disabled until a manual restart is initiated.
Alternatively, the ADM1075 can be set to retry only once by
isolating the LATCH pin from the SHDN pin. The part can
also be configured to retry an infinite number of times with a
10 second interval between restarts by connecting the GPO2
pin to the RESTART pin.
Data Sheet
The ADM1075 has separate UVx and OV pins for undervoltage
and overvoltage detection. The FET is turned off if a nontransient
voltage less than the undervoltage threshold (typically ?35 V) is
detected on the UVx pins or if greater than the overvoltage
threshold (typically ?80 V) is detected on the OV pin. The
operating voltage range of the ADM1075 is programmable via
resistor networks on the UVx and OV pins. The hysteresis levels
on the overvoltage detectors can also be altered by selecting the
appropriate resistors. There are two separate UVx pins to allow
accurate programming of hysteresis.
In the case of a short circuit, the ADM1075 has a fast response
circuit to detect and respond adequately to this event. If the
sense voltage exceeds 1.5 times the normal current limit, a high
current (750 mA minimum) gate pull-down switch is activated
to shut down the MOSFET as quickly as possible. There is a
default internal glitch filter of 900 ns. If a longer filter time or
different severe overcurrent limit is required, these parameters
can be adjusted via the PMBus? interface.
The ADM1075 also includes a 12-bit ADC to provide digital
measurement of the voltage and load current. The current is
measured at the output of the internal current sense amplifier
and the voltage from the ADC_V input. This data can be read
across the PMBus interface.
The PMBus interface allows a controller to read current, voltage,
and power measurements from the ADC. Measurements can be
initiated by a PMBus command or can be set up to run continu-
ously. The user can read the latest conversion data whenever it
is required. A power accumulator is also provided to report
total power consumed in a user specified period (total energy).
Up to four unique I 2 C addresses can be created, depending on
the configuration of the ADR pin.
The GPO1/ALERT1/CONV and GPO2/ALERT2 outputs can
be used as a flag to warn a microcontroller or FPGA of one or
more fault/warning conditions becoming active. The fault type
and level is programmed across the PMBus, and the user can
select which faults/warnings activate the alert.
Other functions include
? PWRGD output, which can be used to enable a power
module (the DRAIN and GATE pins are monitored to
determine when the load capacitance is fully charged)
? SHDN input to manually disable the GATE drive
? RESTART input to remotely initiate a 10 second shutdown
Rev. C | Page 4 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| M1MA174T1 | DIODE SW SS 200MA 100V SOT-323 |
| RCB105DHLD | CONN EDGECARD 210PS DIP .050 SLD |
| VE-24X-CX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| GRM1885C1H681JA01D | CAP CER 680PF 50V 5% NP0 0603 |
| ADM1275-2ARQZ | IC HOT SWAP CTRL PMBUS 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1075-2ARUZ-RL7 | 功能描述:IC HOTSWAP CTRLR -48V 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ADM1085 | 制造商:AD 制造商全称:Analog Devices 功能描述:Simple Sequencers in 6-Lead SC70 |
| ADM1085AKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:SIMPLE SEQUENCER OPEN DRAIN EN IC - Tape and Reel 制造商:Analog Devices 功能描述:IC VOLTAGE SEQUENCER |
| ADM1085AKS-U1 | 制造商:Analog Devices 功能描述:- Bulk |
| ADM1085AKSZ-REEL7 | 功能描述:IC SIMPLE SEQUENCER OD SC70-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Simple Sequencers® 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极，开路漏极 复位:高有效/低有效 复位超时:最小为 250 ms 电压 - 阀值:4.37V，4.62V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 产品目录页面:1337 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。