参数资料
| 型号： | ADM691SQ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU 4.65V 16CDIP |
| 标准包装： | 25 |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 35 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-CDIP |
| 包装： | 管件 |
ADM690–ADM695
Table I. ADM691, ADM693, ADM695 Reset Pulse Width and Watchdog Timeout Selections
Watchdog Timeout Period
Immediately
Reset Active Period
OSC SEL
OSC IN
Normal After Reset
ADM691/ADM693
ADM695
Low
Low
Floating or High
Floating or High
External Clock Input
External Capacitor
Low
Floating or High
1024 CLKS
260 ms × C/47 pF
100 ms
1.6 s
4096 CLKS
1.04 s × C/47 pF
1.6 s
1.6 s
512 CLKS
130 ms × C/47 pF
50 ms
50 ms
2048 CLKS
520 ms × C/47 pF
200 ms
200 ms
NOTE
With the OSC SEL pin low, OSC IN can be driven by an external clock signal, or an external capacitor can be connected between OSC IN and GND. The nominal
internal oscillator frequency is 10.24 kHz. The nominal oscillator frequency with external capacitor is: F OSC (Hz) = 184,000/C (pF).
The watchdog timeout period is fixed at 1.6 seconds, and the
reset pulse width is fixed at 50 ms on the ADM690/ADM692.
On the ADM694 the watchdog timeout period is also 1.6 sec-
onds but the reset pulse width is fixed at 200 ms. The ADM691/
ADM693/ADM695 allow these times to be adjusted as shown
in Table I. Figure 4 shows the various oscillator configurations
8
OSC SEL
ADM691
ADM693
ADM695
which can be used to adjust the reset pulse width and watchdog
timeout period.
C OSC
7
OSC IN
The internal oscillator is enabled when OSC SEL is high or
floating. In this mode, OSC IN selects between the 1.6 second
and 100 ms watchdog timeout periods. With OSC IN connected
high or floating, the 1.6 second timeout period is selected; while
with it connected low, the 100 ms timeout period is selected. In
Figure 4b. External Capacitor
either case, immediately after a reset, the timeout period is 1.6
seconds. This gives the microprocessor time to reinitialize the
system. If OSC IN is low, then the 100 ms watchdog period be-
comes effective after the first transition of WDI. The software
should be written such that the I/O port driving WDI is left in
NC
8
OSC SEL
ADM691
ADM693
ADM695
its power-up reset state until the initialization routines are com-
pleted and the microprocessor is able to toggle WDI at the mini-
NC
7
OSC IN
mum watchdog timeout period of 70 ms.
Watchdog Output (WDO)
The Watchdog Output WDO (ADM691/ADM693/ADM695)
provides a status output which goes low if the watchdog timer
“times out” and remains low until set high by the next transition
Figure 4c. Internal Oscillator (1.6 Second Watchdog)
on the Watchdog Input. WDO is also set high when V CC goes
below the reset threshold.
8
OSC SEL
NC
8
OSC SEL
ADM691
ADM693
ADM695
ADM691
ADM693
7
CLOCK
ADM695
OSC IN
0 TO 250kHz
7
OSC IN
Figure 4d. Internal Oscillator (100 ms Watchdog)
Figure 4a. External Clock Source
REV. A
–7 –
相关PDF资料 |
PDF描述 |
|---|---|
| ADM692SQ | IC SUPERVISOR MPU 4.4V WD 8CDIP |
| ADM696SQ | IC SUPERVISOR MPU 100MA 16CDIP |
| ADM698AN | IC SUPERVISOR MPU 4.65V 8DIP |
| ADM706RAR | IC SUPERVISOR MPU 2.63V WD 8SOIC |
| ADM707AR | IC SUPERVISOR MPU 4.65 WD 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM692 | 制造商:AD 制造商全称:Analog Devices 功能描述:Microprocessor Supervisory Circuits |
| ADM6926 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:26 port 10/100 Mbps Ethernet Switch Controller |
| ADM6926ABT1 | 功能描述:IC SWITCH CNTRLR 10/100 128QFP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| ADM6926X-AB-T-1 | 功能描述:IC ETHERNET SW CTRLR 128-PQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| ADM692A | 制造商:AD 制造商全称:Analog Devices 功能描述:Microprocessor Supervisory Circuits |
发布紧急采购，3分钟左右您将得到回复。