- 您现在的位置：买卖IC网 > PDF目录16950 > ADP1740-1.5-EVALZ (Analog Devices Inc)BOARD EVAL FOR ADP1740-1.5 PDF资料下载
参数资料
| 型号： | ADP1740-1.5-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADP1740-1.5 |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 输出电压： | 1.5V |
| 电流 - 输出： | 2A |
| 输入电压： | 1.6 ~ 3.6 V |
| 稳压器类型： | 正，固定式 |
| 工作温度： | -40°C ~ 125°C |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP1740 |
ADP1740/ADP1741
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Output Capacitor
The ADP1740/ADP1741 are designed for operation with small,
space-saving ceramic capacitors, but they function with most
commonly used capacitors as long as care is taken with regard
to the effective series resistance (ESR) value. The ESR of the
output capacitor affects the stability of the LDO control loop. A
minimum of 3.3 μF capacitance with an ESR of 100 mΩ or less is
recommended to ensure the stability of the ADP1740/ADP1741.
Transient response to changes in load current is also affected by
output capacitance. Using a larger value of output capacitance
improves the transient response of the ADP1740/ADP1741 to
large changes in load current. Figure 33 and Figure 34 show the
transient responses for output capacitance values of 4.7 μF and
22 μF, respectively.
Data Sheet
Input Bypass Capacitor
Connecting a 4.7 μF capacitor from the VIN pin to GND
reduces the circuit sensitivity to printed circuit board (PCB)
layout, especially when long input traces or high source
impedance are encountered. If output capacitance greater than
4.7 μF is required, it is recommended that the input capacitor be
increased to match it.
Input and Output Capacitor Properties
Any good quality ceramic capacitors can be used with the
ADP1740/ADP1741, as long as they meet the minimum
capacitance and maximum ESR requirements. Ceramic
capacitors are manufactured with a variety of dielectrics, each
with different behavior over temperature and applied voltage.
Capacitors must have a dielectric adequate to ensure the
minimum capacitance over the necessary temperature range
1
2
T
I LOAD
1A/DIV
1mA TO 2A LOAD STEP, 2.5A/μs
V OUT
50mV/DIV
and dc bias conditions. X5R or X7R dielectrics with a voltage
rating of 6.3 V or 10 V are recommended. Y5V and Z5U
dielectrics are not recommended, due to their poor temperature
and dc bias characteristics.
of an 0805 case, 4.7 μF, 10 V, X5R capacitor. The voltage stability
of a capacitor is strongly influenced by the capacitor size and
voltage rating. In general, a capacitor in a larger package or with
a higher voltage rating exhibits better stability. The temperature
variation of the X5R dielectric is approximately ±15% over the
CH1 1.0A ? BW CH2 50.0mV
B
V IN = 3.6V, V OUT = 1.5V
C IN = C OUT = 4.7μF
W M1.0μs A CH1 380mA
T 10.80%
?40°C to +85°C temperature range and is not a function of
package size or voltage rating.
5
MURATA P/N GRM219R61A475KE34
Figure 33. Output Transient Response, C OUT = 4.7 μF
4
T
I LOAD
1A/DIV
3
1mA TO 2A LOAD STEP, 2.5A/μs
2
1
1
V OUT
2
50mV/DIV
0
0
2
4
6
8
10
VOLTAGE BIAS (V)
V IN = 3.6V, V OUT = 1.5V
Figure 35. Capacitance vs. Voltage Bias Characteristics
CH1 1.0A ? BW CH2 50.0mV
B
C IN = C OUT = 22μF
W M1.0μs A CH1 880mA
T 11.80%
Use Equation 3 to determine the worst-case capacitance,
accounting for capacitor variation over temperature, com-
Figure 34. Output Transient Response, C OUT = 22 μF
ponent tolerance, and voltage.
C EFF = C OUT × (1 ? TEMPCO ) × (1 ? TOL )
where:
C EFF is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
Rev. F | Page 14 of 20
(3)
相关PDF资料 |
PDF描述 |
|---|---|
| RMA06DRMI-S288 | CONN EDGECARD 12POS .125 EXTEND |
| EYM06DRMD-S664 | CONN EDGECARD 12POS .156 WW |
| GBA31DRSN-S288 | CONN EDGECARD 62POS .125 EXTEND |
| GEM31DTKN-S288 | CONN EDGECARD 62POS .156 EXTEND |
| VI-J5V-EY | CONVERTER MOD DC/DC 5.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1740ACPZ-0.75R7 | 功能描述:IC REG LDO 0.75V 2A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:anyCAP® 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 6V 电压 - 压降（标准）:0.23V @ 1.5A 稳压器数量:1 电流 - 输出:1.5A 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:TO-261-4，TO-261AA 供应商设备封装:SOT-223-3 包装:Digi-Reel® 其它名称:ADP3339AKCZ-3.3-RLDKR |
| ADP1740ACPZ-0.75-R7 | 制造商:AD 制造商全称:Analog Devices 功能描述:2 A, Low VIN, Low Dropout Linear Regulator |
| ADP1740ACPZ-1.0-R7 | 功能描述:IC REG LDO 1V 2A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
| ADP1740ACPZ-1.1-R7 | 功能描述:IC REG LDO 1.1V 2A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:anyCAP® 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 6V 电压 - 压降（标准）:0.23V @ 1.5A 稳压器数量:1 电流 - 输出:1.5A 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:TO-261-4，TO-261AA 供应商设备封装:SOT-223-3 包装:Digi-Reel® 其它名称:ADP3339AKCZ-3.3-RLDKR |
| ADP1740ACPZ-1.2-R7 | 功能描述:IC REG LDO 1.2V 2A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
发布紧急采购，3分钟左右您将得到回复。