- 您现在的位置：买卖IC网 > PDF目录1777 > ADP2127ACNZ-1.20R7 (Analog Devices Inc)IC REG BUCK SYNC 1.2V 0.5A 6EWLP PDF资料下载
参数资料
| 型号： | ADP2127ACNZ-1.20R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 1.2V 0.5A 6EWLP |
| 产品变化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 标准包装： | 3,000 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.2V |
| 输入电压： | 2.1 V ~ 5.5 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 6MHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-SMD，无引线 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 6-WLP Embedded（1.3x0.90） |
Data Sheet
PROTECTION FEATURES
Overcurrent Protection
To ensure that excessively high currents do not damage the
MOSFET switches, the ADP2126 / ADP2127 incorporate cycle-by-
cycle overcurrent protection. This function is accomplished by
monitoring the instantaneous peak current on the power PMOS
switch. If this current exceeds the PMOS switch current limit
(1 A typical), then the PMOS is immediately turned off. This
minimizes the potential for damage to power components during
certain faults and transient events.
Output Short-Circuit Protection (SCP)
If the output voltage is shorted to GND, a standard dc-to-dc
controller delivers maximum power into that short. This may
ADP2126/ADP2127
after VIN. If V IN dips below the UVLO falling threshold and
EXTCLK is powered before VIN with a logic high signal, the
UVLO does not become active. If VIN and EXTCLK are
is recommended to ensure that the ADP2126/ADP2127 are
powered correctly. R τ and C τ should be selected so that the
RC time constant (τ) is greater than the 200 μs minimum
specification for VIN high to EXTCLK on (t 1 ). τ is calculat ed
using the following equation:
τ = R τ × C τ
whe re τ ≥ t 1 .
See Table 1 an d Figure 3 for the timing specifications and
diagrams.
result in a potentially catastrophic failure. To prevent this, the
V IN
A2
VIN
ADP2126/ADP2127 sense when the output voltage is below the
SCP threshold (typically 0.52 V). At this point, the controller
C IN
R
B2
EXTCLK ( OFF
ON
)
turns off for approximately 450 μs and then automatically initiates a
C
soft start sequence. This cycle repeats until the short is removed
or the part is disabled. Figure 16 shows the operating behavior of
C2
GND
the ADP2126/ADP2127 during a short-circuit fault. The SCP
dramatically reduces the power delivered into the short circuit,
yet still allows the converter to recover when the fault is removed.
Thermal Shutdown (TSD) Protection
The ADP2126/ADP2127 also include TSD protection when the
part is in PWM mode only. If the die temperature exceeds 146°C
(typical), the TSD protection activates and turns off both MOSFET
power devices. They remain off until the die temperature falls to
133°C (typical), at which point the regulator restarts.
Undervoltage Lockout (UVLO)
If the input voltage drops below the UVLO falling threshold, the
ADP2126/ADP2127 automatically turn off the power switches and
enter a low power consumption mode. This prevents potentially
erratic operation at low input voltages. The parts remain in this
state until the input voltage rises above the UVLO rising threshold.
The UVLO levels have approximately 100 mV of hysteresis to
ensure glitch-free startup.
For the logic high enable option, during startup and UVLO
recovery after the input voltage drops below the UVLO falling
Figure 29. Recommended Logic Enable Startup Ci rcu it
TIMING CO NSTRAINTS
Shutdown Time
When the ADP212 6/ADP2127 enter shutdown mode after the
EXTCLK signal is removed, the ADP2126/ADP2127 must remain
in shutdown mode for a minimum of 1400 μs, if no load is applied,
before the EXTCLK signal can be reapplied. This allows all internal
nodes to discharge to an off state.
Power-Off Time
When V IN drops, th ereby triggering UVLO, the ADP2126/
ADP2127 have a minimum power-off time (t 7 ) of 500 μs tha t
must elapse before V IN can be reapplied. This allows all intern al
nodes to discharge enough power so that all internal devices are
in an off state.
t 7
V IN × 10%
Figure 30. Power-Off Time
th reshold, EXTCLK must be powered with the logic high signal
Rev. B | Page 13 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| ADP2139ACBZ-3.0-R7 | IC REG BUCK SYNC 3V 0.8A 6WLCSP |
| ADP2147ACBZ-130-R7 | IC REG BUCK SYNC 0.8A 6WLCSP |
| ADP2164ACPZ-1.0-R7 | IC REG BUCK SYNC 1V 4A 16LFCSP |
| ADP220ACBZ-1212R7 | IC REG LDO 1.2V .2A 6WLCSP |
| ADP222ACPZ-2827-R7 | IC REG LDO 2.8V/2.7V .3A 8LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2138 | 制造商:AD 制造商全称:Analog Devices 功能描述:Compact, 800 mA, 3 MHz, Step-Down DC-to-DC Converter |
| ADP2138ACBZ-0.8-R7 | 功能描述:IC REG BUCK SYNC 0.8V .8A 6WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
| ADP2138ACBZ-1.0-R7 | 功能描述:IC REG BUCK SYNC 1V 0.8A 6WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
| ADP2138ACBZ-1.2-R7 | 功能描述:IC REG BUCK SYNC 1.2V .8A 6WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| ADP2138ACBZ-1.5-R7 | 功能描述:IC REG BUCK SYNC 1.5V .8A 6WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
发布紧急采购，3分钟左右您将得到回复。