- 您现在的位置：买卖IC网 > PDF目录17399 > ADP2302-EVALZ (Analog Devices Inc)EVAL BOARD FOR ADP2302 PDF资料下载
参数资料
| 型号： | ADP2302-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR ADP2302 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 电流 - 输出： | 2A |
| 输入电压： | 3 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 700kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP2302 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ADP2302/ADP2303
response and efficiency. Therefore, the inductor value is calculated
CATCH DIODE
Data Sheet
? V IN ? V OUT ?
? ? ? OUT
?
?
using the following equation:
L ?
0 . 3 ? I LOAD (max) ? f sw
? V ? V D
? V IN ? V D
?
?
The catch diode conducts the inductor current during the off
time of the internal MOSFET. The average current of the diode
in normal operation is, therefore, dependent on the duty cycle
of the regulator as well as the output load current.
I DIODE ( AVG ) ? ? ? 1 ? OUT
? ? I LOAD (max)
?
where I LOAD(max) is the maximum load current.
The inductor peak current is calculated using the following
equation:
? V ? V D
? V IN ? V D
?
?
I PEAK ? I LOAD (max) ?
? I RIPPLE
2
where V D is the diode forward drop.
The only reason to select a diode with a higher current rating
The minimum current rating of the inductor must be greater
than the inductor peak current. For ferrite core inductors with a
quick saturation characteristic, the inductor saturation current
rating should be higher than the switch current limit threshold
to prevent the inductor from reaching its saturation point. Be
sure to validate the worst-case condition, in which there is a
shorted output, over the intended temperature range.
Inductor conduction loss is caused by the flow of current
through internal dc resistance (DCR). Larger sized inductors
have smaller DCR of the inductor and, therefore, may reduce
inductor conduction losses. Inductor core loss is related to the
core material and the ac flux swing, which are affected by the
than necessary in normal operation is for the worst-case condi-
tion, in which there is a shorted output. In this case, the diode
current increases up to the typical peak current limit threshold.
Be sure to consult the diode data sheet to ensure that the diode
can operate well within the thermal and electrical limits.
The reverse breakdown voltage rating of the diode must be higher
than the highest input voltage and allow an appropriate margin
for the ringing that may be present on the SW node. A Schottky
diode is recommended for the best efficiency because it has a
provides a list of recommended Schottky diodes.
Table 7. Recommended Schottky Diodes
peak-to-peak inductor ripple current. Because the ADP2302/
ADP2303 are high frequency switching regulators, shielded fer-
rite core materials are recommended for their low core losses
and low EMI. Some recommended inductors are shown in
Vendor
Vishay
ON Semiconductor
Diodes Inc.
Part No.
SSB43L
MBRS330T3
V RRM (V)
30
30
30
30
I AVG (A)
4
3
3
3
Table 8. Recommended Inductors
Vendor
Sumida
Coilcraft
Toko
TDK
Value (μH)
2.5
3.8
5.2
7
10
2.5
3.8
5.2
7
10
2.8
3.7
4.7
6.4
10
2.2
3.3
4.7
6.8
10
Part No.
CDRH104RNP-2R5N
CDRH104RNP-3R8N
CDRH104RNP-5R2N
CDRH104RNP-7R0N
CDRH104RNP-100N
MSS1038-252NL
MSS1038-382NL
MSS1038-522NL
MSS1038-702NL
MSS1038103NL
#919AS-2R8M
#919AS-3R7M
#919AS-4R7M
#919AS-6R4M
#919AS-100M
VLF10040T-2R2N7R1
VLF10040T-3R3N6R2
VLF10040T-4R7N5R4
VLF10040T-6R8N4R5
VLF10040T-100M3R8
DCR (mΩ)
7.8
9.6
16
20
26
10
13
22
27
35
10.7
14.2
16.2
22.9
26.5
7.9
10.5
12.7
19.8
28
I SAT (A)
7.5
6
5.5
4.8
4.4
7.62
6.5
5.28
4.74
3.9
8.3
7
6.1
5.2
4.3
8.2
6.7
5.4
4.6
3.8
Dimensions L × W × H (mm)
10.5 × 10.3 × 3.8
10.5 × 10.3 × 3.8
10.5 × 10.3 × 3.8
10.5 × 10.3 × 3.8
10.5 × 10.3 × 3.8
10 × 10.2 × 3.8
10 × 10.2 × 3.8
10 × 10.2 × 3.8
10 × 10.2 × 3.8
10 × 10.2 × 3.8
10.3 × 10.3 × 4.5
10.3 × 10.3 × 4.5
10.3 × 10.3 × 4.5
10.3 × 10.3 × 4.5
10.3 × 10.3 × 4.5
10 × 9.7 × 4.0
10 × 9.7 × 4.0
10 × 9.7 × 4.0
10 × 9.7 × 4.0
10 × 9.7 × 4.0
Rev. A | Page 18 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| AUIR33401STRR | IC SW IPS 1CH HIGH SIDE D2PAK-7 |
| RSC07DREI-S13 | CONN EDGECARD 14POS .100 EXTEND |
| LQH43CN3R3M03L | INDUCTOR 3.3UH 20% 800MA 1812 |
| SL22HE3/52T | DIODE SCHOTTKY 2A 20V SMB |
| AUIR33401STRL | IC SW IPS 1CH HIGH SIDE D2PAK-7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2303 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA |
| ADP2303ACPZ-R7 | 制造商:Analog Devices 功能描述:ADP2303 3A, 20V NON-SYNC STEP-DOWN DC-DC CONVERTER - Tape and Reel |
| ADP2303ARDZ | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| ADP2303ARDZ-2.5 | 制造商:Analog Devices 功能描述: |
| ADP2303ARDZ-2.5-R7 | 功能描述:IC REG BUCK 2.5V 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
发布紧急采购，3分钟左右您将得到回复。