- 您现在的位置：买卖IC网 > PDF目录17399 > ADP2302-EVALZ (Analog Devices Inc)EVAL BOARD FOR ADP2302 PDF资料下载
参数资料
| 型号： | ADP2302-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/28页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR ADP2302 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 电流 - 输出： | 2A |
| 输入电压： | 3 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 700kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP2302 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
V OUT ? V D
Data Sheet
INPUT CAPACITOR
The input capacitor must be able to support the maximum input
operating voltage and the maximum RMS input current. The
rms ripple current flowing through the input capacitor is, at
maximum, I LOAD(max) /2. Select an input capacitor capable of
withstanding the rms ripple current for an application’s maxi-
mum load current using the following equation:
I IN ( RMS ) ? I LOAD (max) ? D ? ? 1 ? D ?
where D is the duty cycle and is equal to
D ?
V IN ? V D
The recommended input capacitance is ceramic with X5R or X7R
dielectrics due to its low ESR and small temperature coefficients.
A capacitance of 10 μF should be adequate for most applications.
To minimize supply noise, place the input capacitor as close as
possible to the VIN pin of the ADP2302/ADP2303.
OUTPUT CAPACITOR
The output capacitor selection affects both the output voltage ripple
and the loop dynamics of the regulator. The ADP2302/ADP2303
are designed to operate with small ceramic capacitors that have
low ESR and equivalent series inductance (ESL) and are, therefore,
easily able to meet stringent output voltage ripple specifications.
When the regulator operates in continuous conduction mode,
the overall output voltage ripple is the sum of the voltage spike
caused by the output capacitor equivalent series resistance
(ESR) plus the voltage ripple caused by the charging and
discharging of the output capacitor
ADP2302/ADP2303
coefficients. Y5V and Z5U dielectrics are not recommended
because of their poor temperature and dc bias characteristics.
In general, most applications require a minimum output
capacitor value of 2 × 22 μF.
Some recommended output capacitors for V OUT ≤ 5.0 V are
THERMAL CONSIDERATION
ADP2302/ADP2303 have an internal high-side MOSFET and
its drive circuit. Only a small amount of power dissipates inside
the ADP2302/ADP2303 package under typical load conditions,
which reduces thermal constraints.
However, in applications with maximum loads at high ambient
temperature and high duty cycle, the heat dissipated in the
package may cause the junction temperature of the die to
exceed the maximum junction temperature of 125°C. If the
junction temperature exceeds 150°C, the regulator goes into
thermal shutdown and recovers when the junction temperature
drops below 135°C.
The junction temperature of the die is the sum of the ambient
temperature and the temperature rise of the package due to
power dissipation, as indicated in the following equation:
T J = T A + T R
where:
T J is the junction temperature.
T A is the ambient temperature.
T R is the rising temperature of the package due to power
dissipation.
The rising temperature of the package is directly proportional
? V RIPPLE ? ? I RIPPLE ? ? ?
?
?
? 1
? 8 ? f sw ? C OUT
? ESR C OUT
?
?
to the power dissipation in the package. The proportionality
constant for this relationship is the thermal resistance from the
junction of the die to the ambient temperature, as shown in the
Capacitors with lower ESR are preferable to guarantee low
output voltage ripple, as shown in the following equation:
following equation:
T R = θ JA × P D
ESR Cout
?
? V RIPPLE
? I RIPPLE
where:
T R is the rising temperature of the package.
Ceramic capacitors are manufactured with a variety of dielec-
trics, each with different behavior over temperature and applied
voltage. X5R or X7R dielectrics are recommended for best
performance, due to their low ESR and small temperature
Table 9. Recommended Capacitors for V OUT ≤ 5.0 V
θ JA is the thermal resistance from the junction of the die to the
ambient temperature of the package.
P D is the power dissipation in the package.
Vendor
Murata
TDK
Value
22 μF, 6.3 V, X5R
47 μF, 6.3 V, X5R
22 μF, 6.3 V, X5R
33 μF, 6.3 V, X5R
47 μF, 6.3 V, X5R
Part No.
GRM31CR60J226KE19
GRM32ER60J476ME20
C3216X5R0J226MB
C3216X5R0J336MB
C3225X5R0J476MB
Dimensions L × W × H (mm)
3.2 × 2.5 × 2.0
3.2 × 2.5 × 2.0
3.2 × 1.6 × 0.85
3.2 × 1.6 × 1.3
3.2 × 2.5 × 2.5
Rev. A | Page 19 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| AUIR33401STRR | IC SW IPS 1CH HIGH SIDE D2PAK-7 |
| RSC07DREI-S13 | CONN EDGECARD 14POS .100 EXTEND |
| LQH43CN3R3M03L | INDUCTOR 3.3UH 20% 800MA 1812 |
| SL22HE3/52T | DIODE SCHOTTKY 2A 20V SMB |
| AUIR33401STRL | IC SW IPS 1CH HIGH SIDE D2PAK-7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2303 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA |
| ADP2303ACPZ-R7 | 制造商:Analog Devices 功能描述:ADP2303 3A, 20V NON-SYNC STEP-DOWN DC-DC CONVERTER - Tape and Reel |
| ADP2303ARDZ | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| ADP2303ARDZ-2.5 | 制造商:Analog Devices 功能描述: |
| ADP2303ARDZ-2.5-R7 | 功能描述:IC REG BUCK 2.5V 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
发布紧急采购，3分钟左右您将得到回复。