- 您现在的位置：买卖IC网 > PDF目录19369 > ADSP-21060CW-160 (Analog Devices Inc)IC DSP CONTROLLER 32BIT 240CQFP PDF资料下载
参数资料
| 型号： | ADSP-21060CW-160 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/64页 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 32BIT 240CQFP |
| 产品培训模块： | SHARC Processor Overview |
| 标准包装： | 1 |
| 系列： | SHARC® |
| 类型： | 浮点 |
| 接口： | 主机接口，连接端口，串行端口 |
| 时钟速率： | 40MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 512kB |
| 电压 - 输入/输出： | 5.00V |
| 电压 - 核心： | 5.00V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 240-CBFQFP 裸露焊盘 |
| 供应商设备封装： | 240-CQFP（32x32） |
| 包装： | 托盘 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Rev. F
|
Page 13 of 64
|
March 2008
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE
1149.1JTAG test access port of the ADSP-2106x to monitor and
control the target board processor during emulation. The
EZ-ICE probe requires the ADSP-2106x’s CLKIN, TMS, TCK,
TRST, TDI, TDO, EMU, and GND signals be made accessible
on the target system via a 14-pin connector (a 2-row 7-pin strip
header) such as that shown in Figure 5. The EZ-ICE probe plugs
directly onto this connector for chip-on-board emulation. You
must add this connector to your target board design if you
intend to use the ADSP-2106x EZ-ICE. The total trace length
between the EZ-ICE connector and the furthest device sharing
the EZ-ICE JTAG pin should be limited to 15 inches maximum
for guaranteed operation. This length restriction must include
EZ-ICE JTAG signals that are routed to one or more
ADSP-2106x devices, or a combination of ADSP-2106x devices
and other JTAG devices on the chain.
The 14-pin, 2-row pin strip header is keyed at the Pin 3 loca-
tion—Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1
u 0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie, and Samtec. The BTMS, BTCK,
BTRST, and BTDI signals are provided so that the test access
port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins as shown in
Figure 5. If you are not going to use the test access port for
board testing, tie BTRST to GND and tie or pull up BTCK to
VDD. The TRST pin must be asserted (pulsed low) after power-
up (through BTRST on the connector) or held low for proper
operation of the ADSP-2106x. None of the Bxxx pins (Pins 5, 7,
9, and 11) are connected on the EZ-ICE probe.
The JTAG signals are terminated on the EZ-ICE probe as shown
in Table 4.
Figure 6 shows JTAG scan path connections for systems that
contain multiple ADSP-2106x processors.
Connecting CLKIN to Pin 4 of the EZ-ICE header is optional.
The emulator only uses CLKIN when directed to perform oper-
ations such as starting, stopping, and single-stepping multiple
ADSP-2106xs in a synchronous manner. If you do not need
these operations to occur synchronously on the multiple proces-
sors, simply tie Pin 4 of the EZ-ICE header to ground.
If synchronous multiprocessor operations are needed and
CLKIN is connected, clock skew between the multiple
ADSP-2106x processors and the CLKIN pin on the EZ-ICE
header must be minimal. If the skew is too large, synchronous
operations may be off by one or more cycles between proces-
sors. For synchronous multiprocessor operation TCK, TMS,
CLKIN, and EMU should be treated as critical signals in terms
of skew, and should be laid out as short as possible on your
board. If TCK, TMS, and CLKIN are driving a large number of
ADSP-2106xs (more than eight) in your system, then treat them
as a “clock tree” using multiple drivers to minimize skew. (See
Figure 7 and “JTAG Clock Tree” and “Clock Distribution” in
the “High Frequency Design Considerations” section of the
ADSP-2106x User’s Manual, Revision 2.1.)
If synchronous multiprocessor operations are not needed (i.e.,
CLKIN is not connected), just use appropriate parallel termina-
tion on TCK and TMS. TDI, TDO, EMU and TRST are not
critical signals in terms of skew.
For complete information on the SHARC EZ-ICE, see the
ADSP-21000 Family JTAG EZ-ICE User's Guide and Reference.
Figure 5. Target Board Connector for ADSP-2106x EZ-ICE Emulator
(Jumpers in Place)
TOP VIEW
13
14
11
12
910
9
78
56
34
12
EMU
GND
TMS
TCK
TRST
TDI
TDO
GND
KEY (NO PIN)
BTMS
BTCK
BTRST
BTDI
GND
Table 4. Core Instruction Rate/CLKIN Ratio Selection
Signal
Termination
TMS
Driven Through 22
: Resistor (16 mA Driver)
TCK
Driven at 10 MHz Through 22
: Resistor (16 mA
Driver)
TRST1
1 TRST is driven low until the EZ-ICE probe is turned on by the emulator at software
start-up. After software start-up, is driven high.
Active Low Driven Through 22
: Resistor (16 mA
Driver) (Pulled-Up by On-Chip 20 k
: Resistor)
TDI
Driven by 22
: Resistor (16 mA Driver)
TDO
One TTL Load, Split Termination (160/220)
CLKIN
One TTL Load, Split Termination (160/220)
EMU
Active Low 4.7 k
: Pull-Up Resistor, One TTL Load
(Open-Drain Output from the DSP)
相关PDF资料 |
PDF描述 |
|---|---|
| ADSP-21060LCB-133 | IC DSP CONTROLLER 32BIT 225BGA |
| VI-B4Z-CY-F2 | CONVERTER MOD DC/DC 2V 20W |
| ATFC-0402-1N2-BT | INDUCTOR THIN FILM 1.2NH 0402 |
| ADSP-21060LAB-160 | IC DSP CONTROLLER 32BIT 225BGA |
| REC3-1215DRW/H/B | CONV DC/DC 3W 9-18VIN +/-15VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-21060CWZ-133 | 制造商:Analog Devices 功能描述:DSP FLOATING PT 32BIT 33MHZ 240CQFP - Trays |
| ADSP-21060CWZ-160 | 制造商:Analog Devices 功能描述:DSP FLOATING PT 32BIT 40MHZ 40MIPS 240CQFP - Trays |
| ADSP-21060CZ-133 | 功能描述:IC DSP CONTROLLER 32BIT 240CQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21060CZ-160 | 功能描述:IC DSP CONTROLLER 32BIT 240CQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21060CZ-160 | 制造商:Analog Devices 功能描述:Digital Signal Processor IC Supply Volta |
发布紧急采购，3分钟左右您将得到回复。