参数资料
| 型号： | ADUC831BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 57/76页 |
| 文件大小： | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 8x12b，D/A 2x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 包装： | 托盘 |
| 配用： | EVAL-ADUC831QSZ-ND - KIT DEV FOR ADUC831 QUICK START |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页当前第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
REV. 0
–60–
ADuC831
Interrupt Priority
The Interrupt Enable registers are written by the user to enable
individual interrupt sources, while the Interrupt Priority registers
allow the user to select one of two priority levels for each interrupt.
An interrupt of a high priority may interrupt the service routine
of a low priority interrupt, and if two interrupts of different
priority occur at the same time, the higher level interrupt will be
serviced first. An interrupt cannot be interrupted by another
interrupt of the same priority level. If two interrupts of the same
priority level occur simultaneously, a polling sequence is observed
as shown in Table XXXI.
Table XXXI. Priority within an Interrupt Level
Source
Priority
Description
PSMI
1 (Highest)
Power Supply Monitor Interrupt
WDS
2
Watchdog Timer Interrupt
IE0
2
External Interrupt 0
ADCI
3
ADC Interrupt
TF0
4
Timer/Counter 0 Interrupt
IE1
5
External Interrupt 1
TF1
6
Timer/Counter 1 Interrupt
I2CI + ISPI
7
SPI Interrupt
RI + TI
8
Serial Interrupt
TF2 + EXF2 9 (Lowest)
Timer/Counter 2 Interrupt
TII
11 (Lowest)
Time Interval Counter Interrupt
Interrupt Vectors
When an interrupt occurs, the program counter is pushed onto
the stack and the corresponding interrupt vector address is
loaded into the program counter. The Interrupt Vector Addresses
are shown in Table XXXII.
Table XXXII. Interrupt Vector Addresses
Source
Vector Address
IE0
0003H
TF0
000BH
IE1
0013H
TF1
001BH
RI + TI
0023H
TF2 + EXF2
002BH
ADCI
0033H
I2CI + ISPI
003BH
PSMI
0043H
TII
0053H
WDS
005BH
ADuC831 HARDWARE DESIGN CONSIDERATIONS
This section outlines some of the key hardware design consider-
ations that must be addressed when integrating the ADuC831
into any hardware system.
Clock Oscillator
The clock source for the ADuC831 can come either from an
external source or from the internal clock oscillator. To use the
internal clock oscillator, connect a parallel resonant crystal between
XTAL1 and XTAL2, and connect a capacitor from each pin to
ground as shown below.
XTAL2
XTAL1
TO INTERNAL
TIMNG CIRCUITS
ADuC831
Figure 55. External Parallel Resonant Crystal Connections
XTAL2
XTAL1
TO INTERNAL
TIMNG CIRCUITS
ADuC831
EXTERNAL
CLOCK
SOURCE
Figure 56. Connecting an External Clock Source
Whether using the internal oscillator or an external clock
source, the ADuC831’s specified operational clock speed range is
400 kHz to 16 MHz. The core itself is static, and will function
all the way down to dc. But at clock speeds slower that 400 kHz
the ADC will no longer function correctly. Therefore, to ensure
specified operation, use a clock frequency of at least 400 kHz
and no more than 16 MHz. Note: the Flash/EE memory may
not program correctly at a clock frequency of less than 2 MHz.
External Memory Interface
In addition to its internal program and data memories, the ADuC831
can access up to 64 kBytes of external program memory (ROM/
PROM/etc.) and up to 16 MBytes of external data memory (SRAM).
To select from which code space (internal or external program
memory) to begin executing instructions, tie the
EA (external
access) pin high or low, respectively. When
EA is high (pulled up
to VDD), user program execution will start at address 0 of the
internal 62 kBytes Flash/EE code space. When
EA is low (tied
to ground) user program execution will start at address 0 of the
external code space.
A second very important function of the
EA pin is described
in the Single Pin Emulation Mode section.
External program memory (if used) must be connected to the
ADuC831 as illustrated in Figure 57. Note that 16 I/O lines
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC832BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC831BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC831BS | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +12BIT ADC LQFP52 831 |
| ADUC831BS-REEL | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP T/R |
| ADUC831BSZ | 功能描述:IC ADC/DAC 12BIT W/MCU 52-MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC831BSZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 52MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。