- 您现在的位置：买卖IC网 > PDF目录1900 > ADUC832BSZ-REEL (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 52MQFP PDF资料下载
参数资料
| 型号： | ADUC832BSZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 41/92页 |
| 文件大小： | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 52MQFP |
| 标准包装： | 800 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 8x12b，D/A 2x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 52-QFP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
ADuC832
Data Sheet
Rev. B | Page 46 of 92
50
40
60
70
80
90
100
110
TJ JUNCTION TEMPERATURE (°C)
R
E
T
E
NT
IO
N
(
Y
ear
s)
250
200
150
100
50
0
300
ADI SPECIFICATION
100 YEARS MIN.
AT TJ = 55°C
02
98
7-
0
37
Figure 48. Flash/EE Memory Data Retention
USING THE FLASH/EE PROGRAM MEMORY
The 62 kB Flash/EE program memory array is mapped into the
lower 62 kB of the 64 kB program space addressable by the
ADuC832, and is used to hold user code in typical applications.
The program memory Flash/EE memory arrays can be
programmed in three ways: serial downloading, parallel
programming, and user download mode.
Serial Downloading (In-Circuit Programming)
The ADuC832 facilitates code download via the standard
UART serial port. The ADuC832 enters serial download mode
after a reset or power cycle if the PSEN pin is pulled low
through an external 1 kΩ resistor. Once in serial download
mode, the user can download code to the full 62 kB of Flash/EE
program memory while the device is in-circuit in its target
application hardware.
A PC serial download executable is provided as part of the
ADuC832 QuickStart development system. The serial
download protocol is detailed in the MicroConverter uC004
Technical Note, Understanding the Serial Download Protocol.
Parallel Programming
The parallel programming mode is fully compatible with conven-
tional third-party Flash or EEPROM device programmers. In
this mode, Port P0, Port P1, and Port P2 operate as the external
data and address bus interface, ALE operates as the write enable
strobe, and Port P3 is used as a general configuration port that
configures the device for various program and erase operations
during parallel programming. The high voltage (12 V) supply
required for Flash programming is generated using on-chip
charge pumps to supply the high voltage program lines.
The complete parallel programming specification is available at
www.analog.com/microconverter, the MicroConverter home
page.
User Download Mode (ULOAD)
As shown in Figure 49, it is possible to use the 62 kB of
Flash/EE program memory available to the user as one single
block of memory. In this mode, all of the Flash/EE memory is
read only to user code.
However, the Flash/EE program memory can also be written to
during run time simply by entering ULOAD mode. In ULOAD
mode, the lower 56 kB of program memory can be erased and
reprogrammed by user software as shown in Figure 49. ULOAD
mode can be used to upgrade your code in the field via any user
defined download protocol. Configuring the SPI port on the
ADuC832 as a slave, it is possible to completely reprogram the
56 kB of Flash/EE program memory in only 5 seconds (see the
uC007 Technical Note, User Download (ULOAD) Mode).
Alternatively, ULOAD mode can be used to save data to the
56 kB of Flash/EE memory. This can be extremely useful in data
logging applications where the ADuC832 can provide up to
60 kB of NV data memory on chip (4 kB of dedicated Flash/EE
data memory also exist).
The upper 6 kB of the 62 kB of Flash/EE program memory is
only programmable via serial download or parallel programming.
This means that this space appears as read only to user code.
Therefore, it cannot be accidently erased or reprogrammed by
erroneous code execution. This makes it very suitable to use the
6 kB as a bootloader. A bootload enable option exists in the
serial downloader to always run from E000H after reset. If using
a bootloader, this option is recommended to ensure that the
bootloader always executes correct code after reset.
Programming the Flash/EE program memory via ULOAD
mode is described in more detail in the ECON—Flash/EE
Memory Control SFR section and in the uC007 Technical Note,
User Download (ULOAD) Mode.
FFFFH
E000H
DFFFH
0000H
USER BOOTLOADER SPACE
THE USER BOOTLOADER
SPACE CAN BE PROGRAMMED IN
DOWNLOAD/DEBUG MODE VIA THE
KERNEL BUT IS READ ONLY WHEN
EXECUTING USER CODE
6 kBYTE
F800H
F7FFH
USER DOWNLOAD SPACE
EITHER THE DOWNLOAD/DEBUG
KERNEL OR USER CODE (IN
ULOAD MODE) CAN PROGRAM
THIS SPACE.
EMBEDDED DOWNLOAD/DEBUG KERNEL
PERMANENTLY EMBEDDED FIRMWARE ALLOWS
CODE TO BE DOWNLOADED TO ANY OF THE
62 kBYTES OF ON-CHIP PROGRAM MEMORY.
THE KERNEL PROGRAM APPEARS AS 'NOP'
INSTRUCTIONS TO USER CODE.
56 kBYTE
2 kBYTE
62 kBYTES
OF USER
CODE
MEMORY
02
98
7-
0
38
Figure 49. Flash/EE Program Memory Map in ULOAD Mode
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC832QS-U1 | 制造商:Analog Devices 功能描述:EVAL KIT - Bulk |
| ADUC834 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit/24-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC834_02 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual 16-Bit/24-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC834BCP | 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.58MHZ 3.3/5V 56LFCSP - Bulk 制造商:Analog Devices 功能描述: |
| ADUC834BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
发布紧急采购，3分钟左右您将得到回复。