收藏本站
参数资料
型号： ADV7180BSTZ
厂商： Analog Devices Inc
文件页数： 33/116页
文件大小： 0K
描述： IC VIDEO DECODER SDTV 64-LQFP
产品变化通告： ADV7180 Metal Mask Edit 22/Oct/2009
设计资源： Low Cost Differential Video Receiver Using ADA4851 Amplifier and ADV7180 Video Decoder (CN0060)
Low Cost Video Multiplexer for Video Switching Using ADA4853-2 Op Amp with Disable Function (CN0076)
标准包装： 1
类型： 视频解码器
应用： 数码相机，手机，便携式视频
安装类型： 表面贴装
封装/外壳： 64-LQFP
供应商设备封装： 64-LQFP（10x10）
包装： 托盘
产品目录页面： 788 (CN2011-ZH PDF)
配用： EVAL-ADV7180LQEBZ-ND - BOARD EVALUATION ADV7180
EVAL-ADV7180LFEBZ-ND - BOARD EVAL FOR ADV7180 LFCSP
Data Sheet
ADV7180
Rev. I | Page 23 of 116
GLOBAL CONTROL REGISTERS
Register control bits listed in this section affect the whole chip.
POWER-SAVING MODES
Power-Down
PDBP, Address 0x0F[2]
The digital supply of the ADV7180 can be shut down by using
the PWRDWN pin or via I2C1 (see the PWRDWN, Address
0x0F[5] section). PDBP controls whether the I2C control or the
pin has the higher priority. The default is to give the pin
(PWRDWN) priority2. This allows the user to have the
ADV7180 powered down by default at power-up without the
need for an I2C write.
When PDBP is 0 (default), the digital supply power is controlled
by the PWRDWN pin2 (the PWRDWN bit, Address 0x0F[5], is
disregarded).
When PDBP is 1, the PWRDWN bit has priority (the pin is
disregarded).
PWRDWN, Address 0x0F[5]
When PDBP is set to 1, setting the PWRDWN bit switches the
ADV7180 to a chip-wide power-down mode. The power-down
stops the clock from entering the digital section of the chip,
thereby freezing its operation. No I2C bits are lost during power-
down. The PWRDWN bit also affects the analog blocks and
switches them into low current modes. The I2C interface is
unaffected and remains operational in power-down mode.
The ADV7180 leaves the power-down state if the PWRDWN bit is
set to 0 (via I2C) or if the ADV7180 is reset using the RESET pin.
PDBP must be set to 1 for the PWRDWN bit to power down
the ADV7180.
When PWRDWN is 0 (default), the chip is operational. When
PWRDWN is 1, the ADV7180 is in a chip-wide power-down mode.
RESET CONTROL
Reset, Chip Reset, Address 0x0F[7]
Setting this bit, which is equivalent to controlling the RESET pin
on the ADV7180, issues a full chip reset. All I2C registers are reset
to their default/power-up values. Note that some register bits do
not have a reset value specified. They keep their last written value.
Those bits are marked as having a reset value of x in the register
tables (see Table 107 and Table 108). After the reset sequence,
the part immediately starts to acquire the incoming video signal.
1
For 32-lead, I2C is the only power-down option.
2
For 64-lead, 48-lead, and 40-lead only.
After setting the reset bit (or initiating a reset via the RESET pin),
the part returns to the default for its primary mode of operation.
All I2C bits are loaded with their default values, making this bit
self-clearing.
Executing a software reset takes approximately 2 ms. However,
it is recommended to wait 5 ms before any further I2C writes are
performed.
The I2C master controller receives a no acknowledge condition
on the ninth clock cycle when chip reset is implemented (see
the MPU Port Description section).
When the reset bit is 0 (default), operation is normal.
When the reset bit is 1, the reset sequence starts.
GLOBAL PIN CONTROL
Three-State Output Drivers
TOD, Address 0x03[6]
This bit allows the user to three-state the output drivers of the
ADV7180.
Upon setting the TOD bit, the P15 to P0 (P7 to P0 for the 48-lead,
40-lead, and 32-lead devices), HS, VS, FIELD (VS/FIELD pin for
the 48-lead, 40-lead, and 32-lead LFCSP), and SFL pins are
three-stated.
The timing pins (HS, VS, FIELD) can be forced active via the
TIM_OE bit. For more information on three-state control, see
the Three-State LLC Driver and the Timing Signals Output
Enable sections.
Individual drive strength controls are provided via the
DR_STR_x bits.
When TOD is 0 (default), the output drivers are enabled.
When TOD is 1, the output drivers are three-stated.
Three-State LLC Driver
TRI_LLC, Address 0x1D[7]
This bit allows the output drivers for the LLC pin of the
ADV7180 to be three-stated. For more information on three-
state control, refer to the Three-State Output Drivers and the
Timing Signals Output Enable sections.
Individual drive strength controls are provided via the
DR_STR_x bits.
When TRI_LLC is 0 (default), the LLC pin drivers work
according to the DR_STR_C[1:0] setting (pin enabled).
When TRI_LLC is 1, the LLC pin drivers are three-stated.
相关PDF资料
PDF描述
VI-BWR-MX-F3 CONVERTER MOD DC/DC 7.5V 75W
VE-2W3-IW-F1 CONVERTER MOD DC/DC 24V 100W
ADV7611BSWZ-P IC RCVR HDMI 165MHZ LP 64LQFP
MAX3483ECPA+ IC TXRX RS485/422 250KBPS 8-DIP
VI-BWR-MX-F1 CONVERTER MOD DC/DC 7.5V 75W
相关代理商/技术参数
参数描述
ADV7180BSTZ 制造商:Analog Devices 功能描述:Video IC
ADV7180BSTZ-REEL 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 标准包装:250 系列:- 类型:电平移位器 应用:LCD 电视机/监控器 安装类型:表面贴装 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-WQFN（4x4）裸露焊盘 包装:带卷 (TR) 其它名称:296-32523-2TPS65198RUYT-ND
ADV7180KCP32Z 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064
ADV7180KCP32Z-RL 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064
ADV7180KST48Z 功能描述:IC VID DECOD SDTV 10BIT 48LQFP RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*