- 您现在的位置：买卖IC网 > PDF目录20503 > APEK4403GEU-01-T-DK (Allegro Microsystems Inc)BOARD EVAL FOR A4403 PDF资料下载
参数资料
| 型号： | APEK4403GEU-01-T-DK |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR A4403 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输入电压： | 9 V ~ 46 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | A4403 |
| 相关产品： | 620-1273-2-ND - IC REG BUCK ADJ 3A 16QFN |
| 其它名称： | 620-1387 |
A4403
Valley Current Mode Control Buck Converter
In general, the feedback resistors should have the lowest resis-
tance possible, to minimize any noise pick-up effects and to
minimize voltage offsets on the output caused by the bias current,
For example, if you limited I VIN to 250 mA, and assumed V OUT =
5 V and C OUT = 20 μ F, the soft start time could be determined as:
I BIAS , flowing out of the FB node into R6. Reducing the feedback
resistances does introduce another loading effect on the output,
which has an effect on the standby current.
t CHARGE =
20 μ F × 5 V
0.25 A
= 400 μ s
It should be noted that a minimum load of 1 mA is required (see
the Light Load Operation section). This may be provided by the
feedback resistors. For example, if R6 = 750 Ω , this guarantees a
1 mA load current.
Disable The converter is enabled by pulling the DIS pin low.
Once enabled, the output converter is started-up under the control
of the soft-start routine.
To disable the converter, the DIS pin can simply be disconnected
(open circuit).
Soft Start A soft-start routine is initiated when: DIS = 0, no
thermal shutdown exists, and V IN and the internal housekeeping
supplies are above the minimum values. Note that an overcurrent
event does not initiate a soft start, unless the converter is recover-
ing from a thermal shutdown condition.
The soft-start routine controls the rate of rise of the reference
voltage, which in turn controls the output voltage. This function
minimizes the amount of inrush current drawn from VIN and
potential voltage overshoot on the output rail, VOUT.
The soft-start period, T SS , is set by an internal current source
that charges the external capacitor (C5) connected to the SS pin.
Control by the soft-start routine is completed when the SS pin
reaches 0.8 V. The duration of T SS is set by selecting the appro-
priate capacitance, according to the formula:
This means a soft-start duration greater than 400 μ s should be
selected to ensure the inrush current is less than 250 mA.
Shutdown The converter is disabled in the event of either an
overtemperature event, or an undervoltage on VIN (V INUVR ) or
on an internal housekeeping supply.
As soon as any of the above faults have been removed and
assuming DIS = 0, the output voltage, V OUT , is brought-up under
the control of the soft-start routine.
Output Overvoltage Protection In the event of an over-
voltage condition appearing on the output rail, the FB terminal
will also experience the overvoltage, scaled by the feedback resis-
tors. If the FB terminal voltage rises above the nominal voltage
by 10% (typical), the on-time of the buck switch will terminate
and the switch will remain off until the FB voltage reduces to the
correct V FB range.
Switch On-Time and Switching Frequency The switch
on-time effectively determines the operating frequency of the
converter. The selection of the operating frequency is generally
a trade-off between the size of the external passive components
T SS =
C 5 × 0.8
10 ×10 –6
.
(2)
(inductor, and input and output capacitors) and switching losses.
Another consideration in selecting the switching frequency is to
C OUT × V OUT
T on (min) = ? ? OUT
? ×
,
? (4)
?
?
Note: If the soft start function is not required for the application,
a 220 k Ω resistor should be connected between the SS pin and
GND. Without soft start, or with a soft start period that is too
rapid, coupled with a high load that is present during start-up, the
converter may operate in current limit, placing maximum stress
on the input circuit.
Assuming no load is drawn until the start-up process is complete,
the current drawn from the input supply is determined by how
quickly the output capacitors (C3 and C4) are charged. The out-
put capacitors are charged according to the following formula:
t CHARGE = , (3)
I VIN
where I VIN is the input supply current.
ensure that none of the on- or off-time limits are reached under
extreme conditions.
The minimum on-time occurs at maximum input voltage and
minimum load. Consider the following example.
Given:
V IN (max) = 46 V, V OUT = 5 V, f SW = 1 MHz, and:
? V + V f ? 1
V IN + V f f SW
where V f is the voltage drop of the recirculation diode (D1) and
sense resistors (R3 and R4).
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| AT88CK9000-TSU | CRYPTO PROGRAMMER BOARD 3-SOT23 |
| AT25080A-10TU-1.8 | IC EEPROM 8KBIT 20MHZ 8TSSOP |
| 8EWS12STRL | DIODE STD REC 1200V 8A D-PAK |
| AT25040AN-10SU-2.7 | IC EEPROM 4KBIT 20MHZ 8SOIC |
| 8EWS10STRL | DIODE STD REC 1000V 8A D-PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| APEK4447SLJ-01-T-DK | 功能描述:A4447 - DC/DC, Step Down 1, Non-Isolated Outputs Evaluation Board 制造商:allegro microsystems, llc 系列:- 零件状态:有效 主要用途:DC/DC，步降 输出和类型:1，非隔离 功率 - 输出:- 电压 - 输出:0.8 V ~ 24 V 电流 - 输出:2A 电压 - 输入:8 V ~ 50 V 稳压器拓扑:降压 频率 - 开关:- 板类型:完全填充 所含物品:板 使用的 IC/零件:A4447 标准包装:1 |
| APEK4490EES-01-T-DK | 功能描述:BOARD EVAL FOR A4490 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| APEK4491EES-01-T-DK | 功能描述:A4491 - DC/DC, Step Down 3, Non-Isolated Outputs Evaluation Board 制造商:allegro microsystems, llc 系列:- 零件状态:有效 主要用途:DC/DC，步降 输出和类型:3，非隔离 功率 - 输出:- 电压 - 输出:- 电流 - 输出:- 电压 - 输入:4.5 V ~ 23 V 稳压器拓扑:降压 频率 - 开关:550kHz 板类型:完全填充 所含物品:板 使用的 IC/零件:A4491 标准包装:1 |
| APEK4900KLQ-01-T-DK | 功能描述:A4900 - Power Management, Half H-Bridge Driver (External FET) Evaluation Board 制造商:allegro microsystems, llc 系列:- 零件状态:过期 主要用途:电源管理，半 H 桥驱动器（外部 FET） 嵌入式:- 使用的 IC/零件:A4900 主要属性:3 个半 H 桥驱动器 辅助属性:- 所含物品:板 标准包装:1 |
| APEK4910KJP-01-T-DK | 功能描述:A4910 - Power Management, Half H-Bridge Driver (External FET) Evaluation Board 制造商:allegro microsystems, llc 系列:- 零件状态:有效 主要用途:电源管理，半 H 桥驱动器（外部 FET） 嵌入式:- 使用的 IC/零件:A4910 主要属性:3 个半 H 桥驱动器 辅助属性:- 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。