- 您现在的位置：买卖IC网 > PDF目录21928 > AS5030-ATSU (ams)IC ENCODER ROTARY 8-BIT 16-TSSOP PDF资料下载
参数资料
| 型号： | AS5030-ATSU |
| 厂商： | ams |
| 文件页数： | 28/44页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER ROTARY 8-BIT 16-TSSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 标准包装： | 96 |
| 传感范围： | 23.6mT ~ 44.5mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 14mA |
| 电流 - 输出（最大）： | 4mA |
| 输出类型： | 数字，PWM |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AS5030
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.5.3
Magnetic Field Strength Indicators
The AS5030 is not only able to sense the angle of a rotating magnet, it can also measure the magnetic field strength (and hence the vertical
distance) of the magnet.
This extra feature can be used for several purposes:
- as a safety feature by constantly monitoring the presence and proper vertical distance of the magnet
- as a state-of-health indicator, e.g. for a power-up self test
- as a push-button feature for rotate-and-push types of manual input devices
The magnetic field strength information is available in two forms:
Magnetic Field Strength Hardware Indicator: Pin MagRngn (#1) will be ‘high’, when the magnetic field is too weak. The switching limit is
determined by the value of the AGC. If the AGC value is <3F H , the MagRngn output will be ‘low’ (green range), If the AGC is at its upper limit
(3F H ), the MagRngn output will be ‘high’ (red range).
Magnetic Field Strength Software Indicator: D13:D7 in the serial data that is obtained by command READ ANGLE contains the 6-bit
AGC information. The AGC is an automatic gain control that adjusts the internal signal amplitude obtained from the Hall elements to a constant
level. If the magnetic field is weak, e.g. with a large vertical gap between magnet and IC, with a weak magnet or at elevated temperatures of the
magnet, the AGC value will be ‘high’. Likewise, the AGC value will be lower when the magnet is closer to the IC, when strong magnets are used
and at low temperatures.
The best performance of the AS5030 will be achieved when operating within the AGC range. It will still be operational outside the AGC range, but
with reduced performance especially with a weak magnetic field due to increased noise.
Factors Influencing the AGC Value. In practical use, the AGC value will depend on several factors:
?? The initial strength of the magnet. Aging magnets may show a reducing magnetic field over time which results in an increase of
the AGC
value. The effect of this phenomenon is relatively small and can easily be compensated by the AGC.
?? The vertical distance of the magnet. Depending on the mechanical setup and assembly tolerances, there will always be some variation of
the vertical distance between magnet and IC over the lifetime of the application using the AS5030. Again, vertical distance variations can be
compensated by the AGC
?? The temperature and material of the magnet. The recommended magnet for the AS5030 is a diametrically magnetized, 5-6mm diameter
NdFeB (Neodymium-Iron-Boron) magnet. Other magnets may also be used as long as they can maintain to operate the AS5030 within the
AGC range.
Every magnet has a temperature dependence of the magnetic field strength. The temperature coefficient of a magnet depends on the used
material. At elevated temperatures, the magnetic field strength of a magnet is reduced, resulting in an increase of the AGC value. At low
temperatures, the magnetic field strength is increased, resulting in a decrease of the AGC value.
The variation of magnetic field strength over temperature is automatically compensated by the AGC.
OTP Sensitivity Adjustment. To obtain best performance and tolerance against temperature or vertical distance fluctuations, the AGC value
at normal operating temperature should be in the middle between minimum and maximum, hence it should be around 100000 (20 H ).
To facilitate the “vertical centering” of the magnet+IC assembly, the sensitivity of the AS5030 can be adjusted in the OTP register in 4 steps. A
sensitivity adjustment is recommended, when the AGC value at normal operation is close to its lower limit (around 00 H ). The default sensitivity
setting is 00 H = low sensitivity.
8.5.4
“Push-button” Feature
Using the magnetic field strength software and hardware indicators described above, the AS5030 provides a useful method of detecting both
rotation and vertical distance simultaneously. This is especially useful in applications implementing a rotate-and-push type of human interface
(e.g. in panel knobs and switches).
The MagRngn output is ‘high’, when the magnetic field is below the low limit (weak or no magnet) and low when the magnetic field is above the
low limit (in-range or strong magnet).
A finer detection of a vertical distance change, for example when only short vertical strokes are made by the push-button, is achieved by
memorizing the AGC value in normal operation and triggering on a change from that nominal the AGC value to detect a vertical movement.
www.ams.com/AS5030
Revision 2.4
28 - 44
相关PDF资料 |
PDF描述 |
|---|---|
| AS5215OM-HMFP | IC ENCODER PROG 32-VQFN |
| NSE-5310-ASST | IC ENCODER LINEAR 20-TSSOP |
| D2RV-G | BASIC SWITCH |
| D3V-16G4-3C25-K | SWITCH LEVER SPST-NO 16A QC TERM |
| 5053-36-2 | MICROGRABBER/BANANA PLUG 36" RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5030-DB | 功能描述:磁传感器开发工具 AS5030 Demo Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5030-TS_EK_AB | 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5030 标准包装:1 |
| AS5030-TS_EK_DB | 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 7.5V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5030 标准包装:1 |
| AS50-330K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
| AS50-331K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。