参数资料
型号: AS5030-ATSU
厂商: ams
文件页数: 37/44页
文件大小: 0K
描述: IC ENCODER ROTARY 8-BIT 16-TSSOP
应用说明: AS5000 Series Magnet Selection Guide
AS5000 Series Magnets for Extended Vertical Range
标准包装: 96
传感范围: 23.6mT ~ 44.5mT
类型: 线性,旋转编码器 - 可编程
电源电压: 4.5 V ~ 5.5 V
电流 - 电源: 14mA
电流 - 输出(最大): 4mA
输出类型: 数字,PWM
特点: 可编程
工作温度: -40°C ~ 125°C
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 16-TSSOP
包装: 管件
AS5030
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.9.1
Magnet Placement
Ideally, the center of the magnet, the diagonal center of the IC and the rotation axis of the magnet should be in one vertical line.
The lateral displacement of the magnet should be within
± 0.25mm from the IC package center or ± 0.5mm from the IC center, including
the placement of the chip within the IC package.
The vertical distance should be chosen such that the magnetic field on the die surface is within the specified limits. The typical
distance “z” between the magnet and the package surface is 0.5mm to 1.8mm with the recommended magnet (6mm x 2.5mm). Larger gaps are
possible, as long as the required magnetic field strength stays within the defined limits.
A magnetic field outside the specified range may still produce acceptable results, but with reduced accuracy. The out-of-range condition will be
indicated, when the AGC is at the limits
(AGC= 0: field too strong;
AGC=63=(3F H ): field too weak or missing magnet.
Figure 32. Bz Field Distribution Along the X-Axis of a 6mm? Diametric Magnetized Magnet
Figure 32 shows a cross sectional view of the vertical magnetic field component Bz between the north and south pole of a 6mm diameter
magnet, measured at a vertical distance of 1mm. The poles of the magnet (maximum level) are about 2.8mm from the magnet center, which is
almost at the outer magnet edges. The magnetic field reaches a peak amplitude of ~± 106mT at the poles.
The Hall elements are located at a radius of 1mm (indicated as squares at the bottom of the graph). Due to the side view, the two Hall elements
at the Y-axis are overlapping at X = 0mm, therefore only 3 Hall elements are shown.
At 1mm radius, the peak amplitude is ~± 46mT, respectively a differential amplitude of 92mT.
The vertical magnetic field B z follows a fairly linear pattern up to about 1.5mm radius. Consequently, even if the magnet is not perfectly centered,
the differential amplitude will be the same as for a centered magnet.
For example, if the magnet is misaligned in X-axis by -0.5mm, the two X-Hall sensors will measure 70mT (@x = -1.5mm) and
-22mt (@x = -0.5mm). Again, the differential amplitude is 92mT.
At larger displacements however, the B z amplitude becomes nonlinear, which results in larger errors that mainly affect the accuracy of the
system (see also Figure 34 )
www.ams.com/AS5030
Revision 2.4
37 - 44
相关PDF资料
PDF描述
AS5215OM-HMFP IC ENCODER PROG 32-VQFN
NSE-5310-ASST IC ENCODER LINEAR 20-TSSOP
D2RV-G BASIC SWITCH
D3V-16G4-3C25-K SWITCH LEVER SPST-NO 16A QC TERM
5053-36-2 MICROGRABBER/BANANA PLUG 36" RED
相关代理商/技术参数
参数描述
AS5030-DB 功能描述:磁传感器开发工具 AS5030 Demo Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压:
AS5030-TS_EK_AB 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性,旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5030 标准包装:1
AS5030-TS_EK_DB 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性,旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 7.5V 嵌入式:是,MCU,8 位 所含物品:板 使用的 IC/零件:AS5030 标准包装:1
AS50-330K-RC 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors
AS50-331K-RC 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors