参数资料
型号: AS5045-ASST
厂商: ams
文件页数: 21/34页
文件大小: 0K
描述: IC ENCODER PROG 12-BIT 16-SSOP
应用说明: AS5000 Series Magnet Selection Guide
AS5000 Series Magnets for Extended Vertical Range
标准包装: 1
传感范围: 45mT ~ 75mT
类型: 线性,旋转编码器 - 可编程
电源电压: 3 V ~ 3.6 V,4.5 V ~ 5.5 V
电流 - 电源: 21mA
电流 - 输出(最大): 4mA
输出类型: 数字式,PWM,12 位串行
特点: 可编程
工作温度: -40°C ~ 125°C
封装/外壳: 16-SSOP(0.209",5.30mm 宽)
供应商设备封装: 16-SSOP
包装: 标准包装
产品目录页面: 804 (CN2011-ZH PDF)
其它名称: AS5045-ASSTDKR
Following the 18 clock (after reading bit “ccw”), the chip must be reset by disconnecting the power supply.
AS5045
Data Sheet
Figure 12. OTP Programming Connection of AS5045 (shown with AS5045 demoboard)
11.4 Analog Readback Mode
Non-volatile programming (OTP) uses on-chip zener diodes, which become permanently low resistive when
subjected to a specified reverse current.
The quality of the programming process depends on the amount of current that is applied during the programming
process (up to 130mA). This current must be provided by an external voltage source. If this voltage source cannot
provide adequate power, the zener diodes may not be programmed properly.
In order to verify the quality of the programmed bit, an analog level can be read for each zener diode, giving an
indication whether this particular bit was properly programmed or not.
To put the AS5045 in Analog Readback Mode, a digital sequence must be applied to pins CSn, PROG and CLK as
shown in Figure 13 . The digital level for this pin depends on the supply configuration (3.3V or 5V; see section 13
3V / 5V Operation).
The second rising edge on CSn (OutpEN) changes pin PROG to a digital output and the log. high signal at pin PROG
must be removed to avoid collision of outputs (grey area in Figure 13 ).
The following falling slope of CSn changes pin PROG to an analog output, providing a reference voltage V ref , that
must be saved as a reference for the calculation of the subsequent programmed and unprogrammed OTP bits.
Following this step, each rising slope of CLK outputs one bit of data in the reverse order as during programming
(see Figure 10 : Md0-MD1-Div0,Div1-Indx-Z0…Z11, ccw).
If a capacitor is connected to pin PROG, it should be removed during analog readback mode to allow a fast readout
rate. If the capacitor is not removed the analog voltage will take longer to stabilize due to the additional capacitance.
The measured analog voltage for each bit must be subtracted from the previously measured V ref , and the resulting
value gives an indication on the quality of the programmed bit: a reading of <100mV indicates a properly
programmed bit and a reading of >1V indicates a properly unprogrammed bit.
A reading between 100mV and 1V indicates a faulty bit, which may result in an undefined digital value, when the
OTP is read at power-up.
th
www.austriamicrosystems.com
Revision 1.7
20 – 33
相关PDF资料
PDF描述
ASFLM1-12.000MHZ-C OSC MEMS 12.000 MHZ 3.0V SMD
RA202820XX RECTIFIER 2800V 2000A
ASFLM1-27.000MHZ-C OSC MEMS 27.000 MHZ 3.0V SMD
ASFLM1-24.576MHZ-C OSC MEMS 24.576 MHZ 3.0V SMD
RA202625XX RECTIFIER 2600V 2500A
相关代理商/技术参数
参数描述
AS5045ASSU 制造商:AMS 功能描述:IC MAGNETIC ROTARY ENCODER 12BIT SSOP16 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 12BIT SSOP16 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 12BIT SSOP16; IC Function:Encoder IC; Brief Features:360 Contactless High Resolution Angular Position Encoding, Two 12-bit Absolute Output; Supply Voltage Min:3V; Supply Voltage Max:3.6V; No. of Pins:16 ;RoHS Compliant: Yes
AS5045-ASSU 功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点(Brp):- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5045B 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12-Bit Programmable Magnetic Position Sensor
AS5045B-ASSM 制造商:ams 功能描述:T&R / SSOP 16
AS5045B-ASST 制造商:ams 功能描述:T&R / SSOP 16