- 您现在的位置：买卖IC网 > Datasheet目录311 > AS5140 PB (ams)BOARD PROGRAM AS5140 Datasheet资料下载
参数资料
| 型号： | AS5140 PB |
| 厂商： | ams |
| 文件页数： | 17/38页 |
| 文件大小： | 0K |
| 描述： | BOARD PROGRAM AS5140 |
| 标准包装： | 1 |
| 模块/板类型： | 插槽适配器 |
| 适用于相关产品： | AS5000 编程器，AS5140 |
| 其它名称： | AS5140H PB-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
AS5140H
Data Sheet - D e t a i l e d D e s c r i p t i o n
Incremental Power-up Lock Option. After power-up, the incremental outputs can optionally be locked or unlocked, depending on the
status of the CSn pin:
CSn = low at power-up: CSn has an internal pull-up resistor and must be externally pulled low ( R ext ≤ 5k Ω ). If Csn is low at power-up,
the incremental outputs (A, B, Index) will be high until the internal offset compensation is finished. This unique state (A=B=Index = high)
may be used as an indicator for the external controller to shorten the waiting time at power-up. Instead of waiting for the specified maximum
power up-time (0), the controller can start requesting data from the AS5140H as soon as the state (A=B=Index = high) is cleared.
CSn = high or open at power-up: In this mode, the incremental outputs (A, B, Index) will remain at logic high state, until CSn goes low or a
low pulse is applied at CSn. This mode allows intentional disabling of the incremental outputs until, for example the system microcontroller
is ready to receive data.
7.2.3
Incremental Output Hysteresis
To avoid flickering incremental outputs at a stationary magnet position, a hysteresis is introduced. In case of a rotational direction change, the
incremental outputs have a hysteresis of 2 LSB. Regardless of the programmed incremental resolution, the hysteresis of 2 LSB always
corresponds to the highest resolution of 10 bit. In absolute terms, the hysteresis is set to 0.704 degrees for all resolutions. For constant rotational
directions, every magnet position change is indicated at the incremental outputs (see Figure 9) . For example, if the magnet turns clockwise from
position ?x+3“ to ?x+4“, the incremental output would also indicate this position accordingly. A change of the magnet’s rotational direction back to
position “x+3“ means that the incremental output still remains unchanged for the duration of 2 LSB, until position “x+2“ is reached. Following this
direction, the incremental outputs will again be updated with every change of the magnet position.
Figure 9. Hysteresis Window for Incremental Outputs
Incremental
Output
Indication
X+4
X+3
X+2
X+1
Hysteresis:
0.7o
X
X
X+1
X+2
X+3
X+4
X+5
Magnet Position
Clockwise Direction
Counterclockwise Direction
7.3 Pulse Width Modulation (PWM) Output
The AS5140H provides a pulse width modulated output (PWM), whose duty cycle is proportional to the measured angle:
t on ? 1025
( t on + t off )
Position = ------------------------- – 1
The PWM frequency is internally trimmed to an accuracy of ±5% (±10% over full temperature range). This tolerance can be cancelled by
measuring the complete duty cycle as shown above.
(EQ 2)
www.austriamicrosystems.com/AS5140H
Revision 1.4
16 - 37
相关PDF资料 |
PDF描述 |
|---|---|
| ASDMB-ADAPTER-KIT | ASDMB MEMSPEED P II OSC KIT |
| ASFLMPLP-ADAPTER-KIT | ASFLMPLP MEMSPEED P II OSC KIT |
| AT24C01-10SI-1.8 | IC EEPROM 1KBIT 400KHZ 8SOIC |
| AT24C01B-TSU-T | IC EEPROM 1KBIT 1MHZ SOT23-5 |
| AT24C02C-XHM-B | IC EEPROM 2KBIT 1MHZ 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5140-SS_EK_AB | 功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5140 标准包装:1 |
| AS5140-SS_EK_DB | 功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5140 标准包装:1 |
| AS51430FLF | 制造商:TT Electronics / IRC 功能描述:AS51430FLF |
| AS51430HLF | 制造商:TT Electronics / IRC 功能描述:AS51430HLF |
| AS51430JLF | 制造商:TT Electronics / IRC 功能描述:AS51430JLF |
发布紧急采购，3分钟左右您将得到回复。