- 您现在的位置：买卖IC网 > Datasheet目录311 > AS5140 PB (ams)BOARD PROGRAM AS5140 Datasheet资料下载
参数资料
| 型号： | AS5140 PB |
| 厂商： | ams |
| 文件页数： | 21/38页 |
| 文件大小： | 0K |
| 描述： | BOARD PROGRAM AS5140 |
| 标准包装： | 1 |
| 模块/板类型： | 插槽适配器 |
| 适用于相关产品： | AS5000 编程器，AS5140 |
| 其它名称： | AS5140H PB-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
AS5140H
Data Sheet - D e t a i l e d D e s c r i p t i o n
Table 19. OTP Bit Assignment
7.6.2
Bit
17
16
:
0
User Selectable Settings
Symbol
ChipID0
ChipID1
:
ChipID17
mbit0
Function
18 bit Chip ID
Factory Bit
The AS5140H allows programming of the following user selectable options:
- Md1, Md0: Incremental Output Mode Selection.
- Div1, Div0: Divider Setting of Incremental Output.
- Index: Index Pulse Width Selection – 1LSB / 3LSB.
- Z [9:0]: Programmable Zero / Index Position.
- CCW: Counter Clockwise Bit.
ccw=0 – angular value increases in clockwise direction.
ccw=1 – angular value increases in counterclockwise direction.
- RA [4:0]: Redundant Address. An OTP bit location addressed by this address is always set to “1” independent of the corresponding origi-
nal OTP bit setting.
7.6.3
OTP Default Setting
The AS5140H can also be operated without programming. The default, un-programmed setting is as listed below.
-
-
-
-
-
-
7.6.4
Md0, MD1 :00 = Incremental mode = quadrature.
Div0, Div1 :00 = Incremental resolution = 10bit.
Index :0 = Index bit width = 1LSB.
Z9 to Z0 :00 = No programmed zero position.
CCW :0 = Clockwise operation.
RA4 to RA0 :0 = No OTP bit is selected.
Redundant Programming Option
In addition to the regular programming, a redundant programming option is available. This option allows that one selectable OTP bit can be set
to “1” (programmed state) by writing the location of that bit into a 5-bit address decoder. This address can be stored in bits RA5...0 in the OTP
user settings.
Example: Setting RA5…0 to “00001” will select bit 51 = MD0, “00010” selects bit 50 = MD1, “10000” selects bit 36 = CCW, etc.
7.6.5
OTP Register Entry and Exit Condition
To avoid accidental modification of the OTP during normal operation, each OTP access (Load, Write, Read, Program) requires a defined entry
and exit procedure, using the CSn, PROG and CLK signals as shown in Figure 14 .
www.austriamicrosystems.com/AS5140H
Revision 1.4
20 - 37
相关PDF资料 |
PDF描述 |
|---|---|
| ASDMB-ADAPTER-KIT | ASDMB MEMSPEED P II OSC KIT |
| ASFLMPLP-ADAPTER-KIT | ASFLMPLP MEMSPEED P II OSC KIT |
| AT24C01-10SI-1.8 | IC EEPROM 1KBIT 400KHZ 8SOIC |
| AT24C01B-TSU-T | IC EEPROM 1KBIT 1MHZ SOT23-5 |
| AT24C02C-XHM-B | IC EEPROM 2KBIT 1MHZ 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5140-SS_EK_AB | 功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5140 标准包装:1 |
| AS5140-SS_EK_DB | 功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5140 标准包装:1 |
| AS51430FLF | 制造商:TT Electronics / IRC 功能描述:AS51430FLF |
| AS51430HLF | 制造商:TT Electronics / IRC 功能描述:AS51430HLF |
| AS51430JLF | 制造商:TT Electronics / IRC 功能描述:AS51430JLF |
发布紧急采购，3分钟左右您将得到回复。