- 您现在的位置：买卖IC网 > PDF目录19916 > AT18F010-30XU (Atmel)IC FLASH CONFIG 1MBIT 20-TSSOP PDF资料下载
参数资料
| 型号： | AT18F010-30XU |
| 厂商： | Atmel |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC FLASH CONFIG 1MBIT 20-TSSOP |
| 产品变化通告： | AT18F Family Obsolescence 06/Feb/2012 |
| 标准包装： | 74 |
| 可编程类型： | 闪存 |
| 存储容量： | 1Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 609 (CN2011-ZH PDF) |
7
3672A–CNFG–1/08
AT18F010/002/040/080 [Preliminary]
6.6
CEO
Chip Enable Output for configuration download. This output goes Low when the internal address
counter of the device has reached its maximum value which signals that all configuration data is
being clocked out of the device. In a daisy chain of AT18F Series devices, the CEO pin of one
device must be connected to the CE input of the next device in the chain. It will stay Low as long
as CE is Low and OE is High. It will then follow CE until OE goes Low; thereafter, CEO will stay
High until the entire memory device is read again.
6.7
TMS
JTAG Mode Control Input. The state of TMS with the rising edge of TCK determines the state
transitions of the Test Access Port (TAP) controller. TMS has an internal 50 K
weak pull-up to
V
CCJ to provide a logic 1 to the device.
6.8
TCK
JTAG Clock Input. This pin is the JTAG clock input to the TAP controller of the device.
6.9
TDI
JTAG Serial Data Input. This pin is the serial input to all JTAG instructions and data registers. An
internal 50 K
weak pull-up to V
CCJ provides a logic 1 to the device.
6.10
TDO
JTAG Serial Data Output. This pin is the serial output to all JTAG instruction and data registers.
An internal 50 K
weak pull-up to V
CCJ provides a logic 1 to the device if the pin is not driven.
6.11
VCCINT
+3.3V supply voltage for internal logic.
6.12
NC
No Connect Pin. This pin is not connected to any internal logic of the device and can be left
floating.
6.13
VCCO
Supply voltage for I/O drivers (1.8V, 3.3V, or 3.3V).
6.14
VCCJ
Supply voltage for JTAG I/O drivers (1.8V, 3.3V, or 3.3V).
6.15
GND
Power supply ground.
7.
Standby Mode
The AT18F Series Configurators enter a low-power standby mode whenever the JTAG mode is
inactive and CE is asserted High. In this mode, the AT18F Configurator consumes less than 1
mA of current at 3.3V. The output remains in a high-impedance state regardless of the state of
the OE input.
相关PDF资料 |
PDF描述 |
|---|---|
| RE-2405S | CONV DC/DC 1W SNGL 5V OUT SIP7 |
| THJD226K035RJN | CAP TANT 22UF 35V 10% 2917 |
| GEC30DTEH | CONN EDGECARD 60POS .100 EYELET |
| LTC4251-2IS6#TRMPBF | IC CTRLR HOTSWAP NEGVOLT SOT23-6 |
| NCV8502PDW25G | IC REG LDO 2.5V .15A 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT18F040 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:FPGA Configuration Flash Memory |
| AT18F040-30XU | 功能描述:FPGA-配置存储器 4MBits Configurator RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| AT18F080 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:FPGA Configuration Flash Memory |
| AT18F080-30XU | 功能描述:FPGA-配置存储器 8MBits Configurator RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| AT18F-DK3 | 功能描述:可编程逻辑 IC 开发工具 Development Kit for AT18F Series FPGAs RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。