- 您现在的位置：买卖IC网 > Datasheet目录313 > AT45DB642-TC (Atmel)IC FLASH 64MBIT 20MHZ 40TSOP Datasheet资料下载
参数资料
| 型号： | AT45DB642-TC |
| 厂商： | Atmel |
| 文件页数： | 11/37页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 64MBIT 20MHZ 40TSOP |
| 标准包装： | 120 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | DataFLASH |
| 存储容量： | 64M（8192 页 x 1056 字节） |
| 速度： | 20MHz 串行/5MHz 并行 |
| 接口： | 并行/串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 40-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 40-TSOP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AT45DB642
RESET: A low state on the reset pin (RESET) will terminate the operation in progress and
reset the internal state machine to an idle state. The device will remain in the reset condition
as long as a low level is present on the RESET pin. Normal operation can resume once the
RESET pin is brought back to a high level.
The device incorporates an internal power-on reset circuit, so there are no restrictions on the
RESET pin during power-on sequences. The RESET pin is also internally pulled high; there-
fore, in low pin count applications, connection of the RESET pin is not necessary if this pin and
feature will not be utilized. However, it is recommended that the RESET pin be driven high
externally whenever possible.
READY/BUSY: This open drain output pin will be driven low when the device is busy in an
internally self-timed operation. This pin, which is normally in a high state (through an external
pull-up resistor), will be pulled low during programming/erase operations, compare operations,
and page-to-buffer transfers.
The busy status indicates that the Flash memory array and one of the buffers cannot be
accessed; read and write operations to the other buffer can still be performed.
PARALLEL PORT SUPPLY VOLTAGE (VCCP AND GNDP): The VCCP and GNDP pins are
used to supply power for the parallel input/output pins (I/O7-I/O0). The VCCP and GNDP pins
need to be used if the parallel port is to be utilized; however, these pins should be treated as
“ don ’ t connects ” if the SER/PAR pin is not connected or if the SER/PAR pin is always driven
high externally.
Power-on/Reset
State
System
Considerations
When power is first applied to the device, or when recovering from a reset condition, the
device will default to SPI Mode 3 or Inactive Clock Polarity High. In addition, the output pins
(SO or I/O7 - I/O0) will be in a high impedance state, and a high-to-low transition on the CS pin
will be required to start a valid instruction. The SPI mode or the clock polarity mode will be
automatically selected on every falling edge of CS by sampling the inactive Clock State.
The SPI interface is controlled by the serial clock SCK, serial input SI and chip select CS pins.
The sequential 8-bit parallel interface is controlled by the clock CLK, 8 I/Os and chip select CS
pins. These signals must rise and fall monotonically and be free from noise. Excessive noise
or ringing on these pins can be misinterpreted as multiple edges and cause improper opera-
tion of the device. The PC board traces must be kept to a minimum distance or appropriately
terminated to ensure proper operation. If necessary, decoupling capacitors can be added on
these pins to provide filtering against noise glitches.
As system complexity continues to increase, voltage regulation is becoming more important. A
key element of any voltage regulation scheme is its current sourcing capability. Like all Flash
memories, the peak current for DataFlash occur during the programming and erase operation.
The regulator needs to supply this peak current requirement. An under specified regulator can
cause current starvation. Besides increasing system noise, current starvation during program-
ming or erase can lead to improper operation and possible data corruption.
11
1638F – DFLSH – 09/02
相关PDF资料 |
PDF描述 |
|---|---|
| AT88CK9000-8TH | CRYPTO PROGRAMMER BOARD 8-TSSOP |
| AT88SC12816C-MJ | IC EEPROM 128KBIT 1.5MHZ M2J |
| AT88SC25616C-MJ | IC EEPROM 256BIT 1.5MHZ M2J |
| AT88SC3216C-MJ | IC EEPROM 32KBIT 1.5MHZ M2J |
| AT88SC6416C-MJ | IC EEPROM 64KBIT 1.5MHZ M2J |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT45DB642-TI | 功能描述:闪存 64M bit RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| AT45DB64D2-CNU | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-bit Microcontrollers |
| AT45DCB002 | 功能描述:存储卡 2M bit RoHS:否 制造商:Olimex Ltd. 产品:SD 存储容量: 连续读取: 连续写入: 有源模式电流: 工作电源电压: 最大工作温度: 尺寸: |
| AT45DCB002D | 功能描述:存储卡 CARD 2M BYTE RoHS:否 制造商:Olimex Ltd. 产品:SD 存储容量: 连续读取: 连续写入: 有源模式电流: 工作电源电压: 最大工作温度: 尺寸: |
| AT45DCB004 | 功能描述:DATAFLASH CARD 4MEGABYTE RoHS:否 类别:存储卡，模块 >> 存储器，PC 卡 系列:- 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD? |
发布紧急采购，3分钟左右您将得到回复。