收藏本站
参数资料
型号： AT89C51ID2-SLRUM
厂商： Atmel
文件页数： 129/157页
文件大小： 0K
描述： IC 8051 MCU 64K FLASH 44-PLCC
产品培训模块： MCU Product Line Introduction
标准包装： 500
系列： 89C
核心处理器： 8051
芯体尺寸： 8-位
速度： 60MHz
连通性： I²C，SPI，UART/USART
外围设备： POR，PWM，WDT
输入/输出数： 34
程序存储器容量： 64KB（64K x 8）
程序存储器类型： 闪存
EEPROM 大小： 2K x 8
RAM 容量： 2K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振荡器型： 外部
工作温度： -40°C ~ 85°C
封装/外壳： 44-LCC（J 形引线）
包装： 标准包装
其它名称： AT89C51ID2-SLRUMDKR
73
AT89C51ID2
4289C–8051–11/05
and RAM contents are preserved. The status of the Port pins during Power-Down mode
is detailed in Table 57.
Note:
VCC may be reduced to as low as V
RET during Power-Down mode to further reduce
power dissipation. Take care, however, that VDD is not reduced until Power-Down mode
is invoked.
Entering Power-Down Mode
To enter Power-Down mode, set PD bit in PCON register. The AT89C51ID2 enters the
Power-Down mode upon execution of the instruction that sets PD bit. The instruction
that sets PD bit is the last instruction executed.
Exiting Power-Down Mode
Note:
If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until
VCC is restored to the normal operating level.
There are two ways to exit the Power-Down mode:
1.
Generate an enabled external interrupt.
–
The AT89C51ID2 provides capability to exit from Power-Down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and
restores the clocks to the CPU and peripherals. Using INTx# input,
execution resumes when the input is released (see Figure 26). Execution
resumes with the interrupt service routine. Upon completion of the interrupt
service routine, program execution resumes with the instruction immediately
following the instruction that activated Power-Down mode.
Note:
The external interrupt used to exit Power-Down mode must be configured as level sensi-
tive (INT0# and INT1#) and must be assigned the highest priority. In addition, the
duration of the interrupt must be long enough to allow the oscillator to stabilize. The exe-
cution will only resume when the interrupt is deasserted.
Note:
Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM
content.
Figure 26. Power-Down Exit Waveform Using INT1:0#
2.
Generate a reset.
–
A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU
and peripherals. Program execution momentarily resumes with the
instruction immediately following the instruction that activated Power-Down
mode and may continue for a number of clock cycles before the internal
reset algorithm takes control. Reset initializes the AT89C51ID2 and vectors
the CPU to address 0000h.
Note:
During the time that execution resumes, the internal RAM cannot be accessed; however,
it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port
INT1:0#
OSC
Power-down phase
Oscillator restart phase
Active phase
相关PDF资料
PDF描述
AT89C51ID2-RLRUM IC 8051 MCU 64K FLASH 44-VQFP
AT32UC3A364-ALUR IC MCU 64KB FLASH 144LQFP
DS80C310+FCG IC MCU HI SPEED 25MHZ 44-MQFP
D38999/20WD5SN CONN RCPT 5POS WALL MNT W/SCKT
ATMEGA6490-16AUR MCU AVR 64KB FLASH 16MHZ 64TQFP
相关代理商/技术参数
参数描述
AT89C51ID2-SLSIM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-SLSUM 功能描述:8位微控制器 -MCU 64K FLASH 32KHz 3.5-5V Ind. RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51ID2-SMSIM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-UM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51RB2 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*