参数资料
型号: AT89C52-24PC
厂商: Atmel
文件页数: 4/24页
文件大小: 0K
描述: IC MICRO CTRL 24MHZ 40DIP
标准包装: 9
系列: 89C
核心处理器: 8051
芯体尺寸: 8-位
速度: 24MHz
连通性: SIO,UART/USART
输入/输出数: 32
程序存储器容量: 8KB(8K x 8)
程序存储器类型: 闪存
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 4 V ~ 6 V
振荡器型: 内部
工作温度: 0°C ~ 70°C
封装/外壳: 40-DIP(0.600",15.24mm)
包装: 管件
AT89C52
12
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively,
of an inverting amplifier that can be configured for use as
an on-chip oscillator, as shown in Figure 7. Either a quartz
crystal or ceramic resonator may be used. To drive the
device from an external clock source, XTAL2 should be left
unconnected while XTAL1 is driven, as shown in Figure 8.
There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry
is through a divide-by-two flip-flop, but minimum and maxi-
mum voltage high and low time specifications must be
observed.
Idle Mode
In idle mode, the CPU puts itself to sleep while all the on-
chip peripherals remain active. The mode is invoked by
software. The content of the on-chip RAM and all the spe-
cial functions registers remain unchanged during this
mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
Note that when idle mode is terminated by a hardware
reset, the device normally resumes program execution
from where it left off, up to two machine cycles before the
internal reset algorithm takes control. On-chip hardware
inhibits access to internal RAM in this event, but access to
the port pins is not inhibited. To eliminate the possibility of
an unexpected write to a port pin when idle mode is termi-
nated by a reset, the instruction following the one that
invokes idle mode should not write to a port pin or to exter-
nal memory.
Power-down Mode
In the power-down mode, the oscillator is stopped, and the
instruction that invokes power-down is the last instruction
executed. The on-chip RAM and Special Function Regis-
ters retain their values until the power-down mode is
terminated. The only exit from power-down is a hardware
reset. Reset redefines the SFRs but does not change the
on-chip RAM. The reset should not be activated before V
CC
is restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and
stabilize.
Figure 7. Oscillator Connections
Note:
C1, C2 = 30 pF
± 10 pF for Crystals
= 40 pF
± 10 pF for Ceramic Resonators
Figure 8. External Clock Drive Configuration
C2
XTAL2
GND
XTAL1
C1
XTAL2
XTAL1
GND
NC
EXTERNAL
OSCILLATOR
SIGNAL
Status of External Pins During Idle and Powe-down Modes
Mode
Program Memory
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
Data
Idle
External
1
Float
Data
Address
Data
Power-down
Internal
0
Data
Power-down
External
0
Float
Data
相关PDF资料
PDF描述
AT89C52-24JI IC MICRO CTRL 24MHZ 44PLCC
AT89C52-24AC IC MICRO CTRL 24MHZ 44TQFP
AT89C51-24PC IC MICRO CTRL 24MHZ 40DIP
AT89C51-24JC IC MICRO CTRL 24MHZ 44PLCC
PIC16C711-04/SS IC MCU OTP 1KX14 A/D 20SSOP
相关代理商/技术参数
参数描述
AT89C52-24PI 功能描述:8位微控制器 -MCU 8K Flash 24M RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C52-24PU 制造商:Atmel Corporation 功能描述:8051 MCU W/ 8K FLASH - 24MHZ PDIP IND TE
AT89C52-24QC 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C52-24QI 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 8K Bytes Flash
AT89C52-33AC 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT