收藏本站
参数资料
型号： ATTINY2313A-MMHR
厂商： Atmel
文件页数： 4/172页
文件大小： 0K
描述： IC MCU AVR 2K FLASH 3X3 20QFN
产品培训模块： tinyAVR Introduction
标准包装： 1
系列： AVR® ATtiny
核心处理器： AVR
芯体尺寸： 8-位
速度： 20MHz
连通性： I²C，SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，WDT
输入/输出数： 18
程序存储器容量： 2KB（1K x 16）
程序存储器类型： 闪存
EEPROM 大小： 128 x 8
RAM 容量： 128 x 8
电压 - 电源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 20-VFQFN 裸露焊盘
包装： 标准包装
其它名称： ATTINY2313A-MMHRDKR
101
8246B–AVR–09/11
ATtiny2313A/4313
The OCR1A Register however, is double buffered. This feature allows the OCR1A I/O location
to be written anytime. When the OCR1A I/O location is written the value written will be put into
the OCR1A Buffer Register. The OCR1A Compare Register will then be updated with the value
in the Buffer Register at the next timer clock cycle the TCNT1 matches TOP. The update is done
at the same timer clock cycle as the TCNT1 is cleared and the TOV1 flag is set.
Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using
ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However,
if the base PWM frequency is actively changed (by changing the TOP value), using the OCR1A
as TOP is clearly a better choice due to its double buffer feature.
In fast PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins.
Setting the COM1x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output
can be generated by setting the COM1x1:0 to three (see Table 12-2 on page 111). The actual
OC1x value will only be visible on the port pin if the data direction for the port pin is set as output
(DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x Register at
the compare match between OCR1x and TCNT1, and clearing (or setting) the OC1x Register at
the timer clock cycle the counter is cleared (changes from TOP to BOTTOM).
The PWM frequency for the output can be calculated by the following equation:
The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x Register represents special cases when generating a PWM
waveform output in the fast PWM mode. If the OCR1x is set equal to BOTTOM (0x0000) the out-
put will be a narrow spike for each TOP+1 timer clock cycle. Setting the OCR1x equal to TOP
will result in a constant high or low output (depending on the polarity of the output set by the
COM1x1:0 bits.)
A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-
ting OCF1A to toggle its logical level on each compare match (COM1A1:0 = 1). The waveform
generated will have a maximum frequency of f
OC1A = fclk_I/O/2 when OCR1A is set to zero
(0x0000). This feature is similar to the OCF1A toggle in CTC mode, except the double buffer
feature of the Output Compare unit is enabled in the fast PWM mode.
12.8.4
Phase Correct PWM Mode
The phase correct Pulse Width Modulation or phase correct PWM mode (WGM13:0 = 1, 2, 3,
10, or 11) provides a high resolution phase correct PWM waveform generation option. The
phase correct PWM mode is, like the phase and frequency correct PWM mode, based on a dual-
slope operation. The counter counts repeatedly from BOTTOM (0x0000) to TOP and then from
TOP to BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC1x) is
cleared on the compare match between TCNT1 and OCR1x while upcounting, and set on the
compare match while downcounting. In inverting Output Compare mode, the operation is
inverted. The dual-slope operation has lower maximum operation frequency than single slope
operation. However, due to the symmetric feature of the dual-slope PWM modes, these modes
are preferred for motor control applications.
The PWM resolution for the phase correct PWM mode can be fixed to 8-, 9-, or 10-bit, or defined
by either ICR1 or OCR1A. The minimum resolution allowed is 2-bit (ICR1 or OCR1A set to
f
OCnxPWM
fclk_I/O
N
1
TOP
+
()
-----------------------------------
=
相关PDF资料
PDF描述
ATTINY26-16MQR IC MCU AVR 2K 16MHZ IND 32QFN
ATTINY26L-8PU IC MCU AVR 2K 5V 8MHZ 20-DIP
ATTINY28V-1AUR IC MCU AVR 2K 1.2MHZ 1.8V 32TQFP
ATTINY4313-MMH IC MCU AVR 4K FLASH 20QFN
ATTINY43U-SUR MCU AVR 4KB FLASH 8MHZ 20SOIC
相关代理商/技术参数
参数描述
ATTINY2313A-MU 功能描述:8位微控制器 -MCU 2K FLASH 128B EE 128B SRAM 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY2313A-MUR 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM 1UART20MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY2313A-PU 功能描述:8位微控制器 -MCU 2K FLASH 128B EE 128B SRAM 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY2313A-SU 功能描述:8位微控制器 -MCU 2K FLASH 128B EE 128B SRAM 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY2313A-SUR 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM 1UART20MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*