参数资料
| 型号： | ATTINY84A-SSU |
| 厂商： | Atmel |
| 文件页数： | 65/135页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT 8K FLASH 14SOIC |
| 标准包装： | 55 |
| 系列： | AVR® ATtiny |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 连通性： | USI |
| 外围设备： | 欠压检测/复位，POR，PWM，温度传感器，WDT |
| 输入/输出数： | 12 |
| 程序存储器容量： | 8KB（4K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页当前第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页
34
8183F–AVR–06/12
ATtiny24A/44A/84A
the Analog Comparator can be powered down by setting the ACD bit in “ACSR – Analog Com-
parator Control and Status Register” on page 129. This will reduce power consumption in Idle
mode. If the ADC is enabled, a conversion starts automatically when this mode is entered.
7.1.2
ADC Noise Reduction Mode
When the SM[1:0] bits are written to 01, the SLEEP instruction makes the MCU enter ADC
Noise Reduction mode, stopping the CPU but allowing the ADC, the external interrupts, and the
Watchdog to continue operating (if enabled). This sleep mode halts clk
I/O, clkCPU, and clkFLASH,
while allowing the other clocks to run.
This improves the noise environment for the ADC, enabling higher resolution measurements. If
the ADC is enabled, a conversion starts automatically when this mode is entered. Apart form the
ADC Conversion Complete interrupt, only an External Reset, a Watchdog Reset, a Brown-out
Reset, an SPM/EEPROM ready interrupt, an external level interrupt on INT0 or a pin change
interrupt can wake up the MCU from ADC Noise Reduction mode.
7.1.3
Power-Down Mode
When the SM[1:0] bits are written to 10, the SLEEP instruction makes the MCU enter Power-
down mode. In this mode, the Oscillator is stopped, while the external interrupts, and the Watch-
dog continue operating (if enabled). Only an External Reset, a Watchdog Reset, a Brown-out
Reset, an external level interrupt on INT0, or a pin change interrupt can wake up the MCU. This
sleep mode halts all generated clocks, allowing operation of asynchronous modules only.
7.1.4
Standby Mode
When the SM[1:0] bits are 11 and an external crystal/resonator clock option is selected, the
SLEEP instruction makes the MCU enter Standby mode. This mode is identical to Power-down
with the exception that the Oscillator is kept running. From Standby mode, the device wakes up
in six clock cycles.
7.2
Software BOD Disable
When the Brown-out Detector (BOD) is enabled by BODLEVEL fuses (see Table 19-4 on page
159), the BOD is actively monitoring the supply voltage during a sleep period. In some devices it
is possible to save power by disabling the BOD by software in Power-Down and Stand-By sleep
modes. The sleep mode power consumption will then be at the same level as when BOD is glob-
ally disabled by fuses.
If BOD is disabled by software, the BOD function is turned off immediately after entering the
sleep mode. Upon wake-up from sleep, BOD is automatically enabled again. This ensures safe
operation in case the V
CC level has dropped during the sleep period.
When the BOD has been disabled, the wake-up time from sleep mode will be approximately
60s to ensure that the BOD is working correctly before the MCU continues executing code.
BOD disable is controlled by the BODS (BOD Sleep) bit of MCU Control Register, see “MCUCR
– MCU Control Register” on page 36. Writing this bit to one turns off BOD in Power-Down and
Stand-By, while writing a zero keeps the BOD active. The default setting is zero, i.e. BOD active.
Writing to the BODS bit is controlled by a timed sequence and an enable bit, see “MCUCR –
相关PDF资料 |
PDF描述 |
|---|---|
| 516-230-256 | CONN COVER PLASTIC 56POS TOP |
| ATTINY2313A-SU | IC MCU AVR 2K FLASH 20MHZ 20SOIC |
| ATTINY24A-MF | MCU AVR 2KB FLASH 20MHZ 20QFN |
| 516-230-138 | CONN COVER PLASTIC 38POS SIDE |
| 516-230-212 | CONN COVER PLASTIC 120POS TOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATTINY84A-SSUR | 功能描述:8位微控制器 -MCU 20MHz Ind. Grade RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATTINY84-ESMZ | 制造商:Atmel Corporation 功能描述: |
| ATTINY84V | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| ATTINY84V-10MU | 功能描述:8位微控制器 -MCU AVR 8K FLSH 512B EE 512B SRAM 1.8V 10MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATTINY84V-10MU SL383 | 制造商:Atmel Corporation 功能描述:8BIT ATTINY RISC 8KB FLASH 10MHZ 2.5/3.3/5V 20QFN - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。