- 您现在的位置：买卖IC网 > Datasheet目录396 > ATZB-900-B0 (Atmel)KIT MOD 802.15.4/ZIGB 900MHZ RF Datasheet资料下载
参数资料
| 型号： | ATZB-900-B0 |
| 厂商： | Atmel |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | KIT MOD 802.15.4/ZIGB 900MHZ RF |
| 标准包装： | 1 |
| 频率： | 779MHz ~ 787MHz，868MHz ~ 868.6MHz，902MHz ~ 928MHz |
| 数据传输率 - 最大： | 250kbps |
| 调制或协议： | 802.15.4 Zigbee |
| 应用： | 住宅/楼宇自动化，工业控制和监控 |
| 功率 - 输出： | 11dBm |
| 灵敏度： | -110dBm |
| 电源电压： | 1.8 V ~ 3.6 V |
| 电流 - 接收： | 15mA |
| 电流 - 传输： | 20mA |
| 数据接口： | PCB，表面贴装 |
| 存储容量： | 128kB 闪存，8kB RAM，4kB EEPROM |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | PCB 模块 |
| 包装： | 散装 |
Specifications
5. It is strongly recommended to avoid assigning an alternate function for OSC32K_OUT pin because it is
used by BitCloud. However, this signal can be used if another peripheral or host processor requires
32.768 kHz clock, otherwise this pin can be disconnected.
6. Normally, JTAG_TMS, JTAG_TDI, JTAG_TDO, JTAG_TCK pins are used for on-chip debugging and
flash burning. They can be used for A/D conversion if JTAGEN fuse is disabled.
7. The following pins can be configured with the BitCloud software to be general-purpose I/O lines:
GPIO0, GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, GPIO7, GPIO8, GPIO_1WR, I2C_CLK,
I2C_DATA, UART_TXD, UART_RXD, UART_RTS, UART_CTS, ADC_INPUT_3, ADC_INPUT_2,
ADC_INPUT_1, BAT, UART_DTR, USART0_RXD, USART0_TXD, USART0_EXTCLK, IRQ_7, IRQ_6.
Additionally, four JTAG lines can be programmed with software as GPIO as well, but this requires
changing the fuse bits and will disable JTAG debugging.
8. With BitCloud, CTS pin can be configured to indicate sleep/active condition of the module thus provid-
ing mechanism for power management of host processor. If this function is necessary, connection of
this pin to external pull-down resistor is recommended to prevent the undesirable transients during
module reset process.
9. Using ferrite bead and 1 μF capacitor located closely to the power supply pin is recommended, as
shown below.
10. In SPI mode, USART0_EXTCLK is output. In USART mode, this pin can be configured as either input or
output pin.
ZigBit? 700/800/900 MHz Wireless Modules
3-8
8227C–MCU Wireless–06/09
相关PDF资料 |
PDF描述 |
|---|---|
| AUIRF7640S2TR1 | MOSFET N-CH 60V 77A DIRECTFET-S2 |
| AUIRF7665S2TR1 | MOSFET N-CH 100V 77A DIRECTFET2 |
| AUIRFR120ZTR | MOSFET N-CH 100V 8.7A DPAK |
| AUIRFR4105ZTR | MOSFET N-CH 55V 30A DPAK |
| AUIRLR024NTR | MOSFET N-CH 55V 17A DPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATZB-900-B0R | 功能描述:Zigbee/802.15.4模块 ZigBit 900 Balanced Output RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| ATZB-A-233-XPRO | 制造商:Atmel Corporation 功能描述:XPLAINED PRO EXT AMP RF233 ZIGBIT - Boxed Product (Development Kits) |
| ATZB-A24-U0 | 功能描述:Zigbee/802.15.4模块 ZigBit Amp 2.4 GHz Unbalanced Output RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| ATZB-A24-U0B | 制造商:Atmel Corporation 功能描述:ZIGBIT 2.4GHZ AMPLIFIED WIRELESS MODULES 制造商:Atmel Corporation 功能描述:ZIGBIT AMP 2.4 GHZ UNBAL OUTPUT REV B - Boxed Product (Development Kits) 制造商:Atmel Corporation 功能描述:MODULE ZIGBIT AMP 2.4GHZ UNBAL 制造商:Atmel Corporation 功能描述:ZigBit Amp 2.4 GHz Unbal Output Rev B |
| ATZB-A24-U0BR | 制造商:Atmel Corporation 功能描述:ZIGBIT AMP 2.4 GHZ UNBAL OUTPU 制造商:Atmel Corporation 功能描述:ZIGBIT AMP 2.4 GHZ UNBAL OUTPUT REV B T& - Boxed Product (Development Kits) 制造商:Atmel Corporation 功能描述:MODULE ZIGBIT AMP 2.4GHZ UNBAL 制造商:Atmel Corporation 功能描述:ZigBit Amp 2.4 GHz Unbal Output Rev B |
发布紧急采购，3分钟左右您将得到回复。