参数资料
| 型号： | B048F240T30 |
| 厂商： | Vicor Corporation |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | CONVERTER BUS 24V OUT 300W SMD |
| 应用说明： | Factorized Power Architecture and V-I Chips |
| 产品培训模块： | VI Chip Bus Converter Modules |
| 标准包装： | 1 |
| 系列： | V-I Chip™, BCM™ |
| 类型： | 总线转换器模块 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 38V |
| 电压 - 输入（最大）： | 53V |
| 输出电压： | 24V |
| 电流 - 输出（最大）： | 12.5A |
| 电源（瓦） - 制造商系列： | 300W |
| 电压 - 隔离： | 2.25kV（2250V） |
| 应用： | 商用 |
| 特点： | 具有远程开/关功能和 UVLO |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 模块 |
| 尺寸/尺寸： | 1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 125°C |
| 效率： | 95.8% |
| 电源（瓦特）- 最大： | 300W |
| 重量： | 0.033 磅（14.97g） |
| 其它名称： | 1102-1002 |
Not Recommended for New Designs - Replaced by BCM48Bx240y300A00
Application Note
B048F240T30
Parallel Operation
The BCM ? bus converter will inherently current share when operated in
an array. Arrays may be used for higher power or redundancy in an
application.
Current sharing accuracy is maximized when the source and load
impedance presented to each bus converter within an array are equal.
The recommended method to achieve matched impedances is to
dedicate common copper planes within the PCB to deliver and return
the current to the array, rather than rely upon traces of varying lengths.
In typical applications the current being delivered to the load is larger
than that sourced from the input, allowing traces to be utilized on the
input side if necessary. The use of dedicated power planes is, however,
preferable.
The bus converter power train and control architecture allow bi-
directional power transfer, including reverse power processing from the
module output to its input. Reverse power transfer is enabled if the
module input is within its operating range and the module is otherwise
enabled. The bus converter’s ability to process power in reverse
improves the module’s transient response to an output load dump.
Thermal Considerations
VI Chip products are multi-chip modules whose temperature
distribution varies greatly for each part number as well as with the
input /output conditions, thermal management and environmental
conditions. Maintaining the top of the B048F240T30 case to less than
100°C will keep all junctions within the module below 125°C for most
applications. The percent of total heat dissipated through the top
surface versus through the J-lead is entirely dependent on the particular
mechanical and thermal environment. The heat dissipated through the
top surface is typically 60%. The heat dissipated through the J-lead
onto the PCB board surface is typically 40%. Use 100% top surface
dissipation when designing for a conservative cooling solution.
It is not recommended to use a module for an extended period of time
at full load without proper heat sinking.
Input Impedance Recommendations
To take full advantage of the BCM bus converter capabilities, the
impedance presented to its input terminals must be low from DC to
approximately 5 MHz. The source should exhibit low inductance and
should have a critically damped response. If the interconnect inductance
is excessive, the module input pins should be bypassed with an RC
damper (e.g., 47 μF in series with 0.3 ohm) to retain low source
impedance and proper operation. Given the wide bandwidth of the
module, the source response is generally the limiting factor in the
overall system response.
Anomalies in the response of the source will appear at the output of
the module multiplied by its K factor. The DC resistance of the source
should be kept as low as possible to minimize voltage deviations. This is
especially important if the module is operated near low or high line as
the overvoltage /undervoltage detection circuitry could be activated.
Input Fuse Recommendations
VI Chip modules are not internally fused in order to provide flexibility in
configuring power systems. However, input line fusing of the modules
must always be incorporated within the power system. A fast acting
fuse should be placed in series with the +In port.
BCM ? Bus Converter
Page 10 of 12
Rev 2.8
01/2014
vicorpower.com
800 927.9474
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T21B11A | CONN HSG RCPT 11POS JAMNUT PINS |
| VE-24D-MV-F2 | CONVERTER MOD DC/DC 85V 150W |
| M83723/91W2212NLC | CONN HSG PLUG 12POS STRGHT SCKT |
| VE-24D-MV-F1 | CONVERTER MOD DC/DC 85V 150W |
| MS3456W16-10B | CONN HSG PLUG 3POS STRGHT SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B048F240T30_12 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:Bus Converter |
| B048F240T30A | 功能描述:BCM BUS CONVERTER 24V 300W 制造商:vicor corporation 系列:VI Chip? BCM? 包装:散装 零件状态:有效 类型:总线转换器模块 输出数:1 电压 - 输入（最小值）:38V 电压 - 输入（最大值）:55V 电压 - 输出 1:24V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:12.5A 功率（W） - 制造系列:300W 电压 - 隔离:2.25kV（2250V） 应用:ITE（商业） 特性:远程开/关，OCP，OTP，OVP，SCP，UVLO 安装类型:表面贴装 封装/外壳:模块 大小/尺寸:1.28" 长 x 0.87" 宽 x 0.26" 高（32.5mm x 22.0mm x 6.7mm） 工作温度:-40°C ~ 125°C 效率:95.5% 功率（W） - 最大值:300W 标准包装:1 |
| B048F240T30-EB | 功能描述:EVAL BOARD 24V OUT 300W SMD RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, BCM™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| B048F320M30 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:BCM Bus Converter |
| B048F320M30A | 功能描述:BCM BUS CONVERTER 32V 300W 制造商:vicor corporation 系列:VI Chip? BCM? 包装:散装 零件状态:有效 类型:总线转换器模块 输出数:1 电压 - 输入（最小值）:38V 电压 - 输入（最大值）:55V 电压 - 输出 1:32V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:9A 功率（W） - 制造系列:300W 电压 - 隔离:2.25kV（2250V） 应用:ITE（商业） 特性:远程开/关，OCP，OTP，OVP，SCP，UVLO 安装类型:表面贴装 封装/外壳:模块 大小/尺寸:1.28" 长 x 0.87" 宽 x 0.26" 高（32.5mm x 22.0mm x 6.7mm） 工作温度:-55°C ~ 125°C 效率:96.2% 功率（W） - 最大值:300W 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。