参数资料
| 型号： | BD3508MUV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 16/21页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 3A 20QFN |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 0.65 V ~ 2.7 V |
| 输入电压： | 0.75 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.065 @ 1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 3A（最小） |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 供应商设备封装： | 20-VQFN |
| 包装： | 带卷 (TR) |
BD3508MUV,BD3509MUV
Technical Note
● Heat Loss
Thermal design should allow operation within the following conditions. Note that the temperatures listed are the allowed
temperature limits, and thermal design should allow sufficient margin from the limits.
1. Ambient temperature Ta can be no higher than 100 ℃ .
2. Chip junction temperature (Tj) can be no higher than 150 ℃ .
Chip junction temperature can be determined as follows:
① Calculation based on ambient temperature (Ta)
＜ Reference values ＞
Tj=Ta+ θ j-a × W
4-layer substrate (bottom layer surface copper foil area 10.29mm )
4-layer substrate (bottom layer surface copper foil area 10.29mm )
4-layer substrate (top layer copper foil area 5505mm )
θ j-a: VQFN020V4040 367.6 ℃ /W
178.6 ℃ /W
103.3 ℃ /W
35.1 ℃ /W
Bare (unmounted) IC
2
2
2
Substrate size: 74.2 × 74.2 × 1.6mm (substrate with thermal via)
3
It is recommended to layout the VIA for heat radiation in the GND pattern of reverse (of IC) when there is the GND pattern in
the inner layer (in using multiplayer substrate). This package is so small (size: 4.2mm × 4.2mm) that it is not available to
layout the VIA in the bottom of IC. Spreading the pattern and being increased the number of VIA like the figure below).
enable to get the superior heat radiation characteristic. (This figure is the image. It is recommended that the VIA size and the
number is designed suitable for the actual situation.).
Most of the heat loss that occurs in the BD3509MUV is generated from the output Nch FET. Power loss is determined by the
total VIN-Vo voltage and output current. Be sure to confirm the system input and output voltage and the output current
conditions in relation to the heat dissipation characteristics of the VIN and Vo in the design. Bearing in mind that heat
dissipation may vary substantially depending on the substrate employed (due to the power package incorporated in the
BD3509MUV) make certain to factor conditions such as substrate size into the thermal design.
Power consumption (W) =
Input voltage (VIN)- output voltage (Vo)
× Io (Ave)
Example) VIN=1.5V, Vo=1.25V, Io(Ave) = 4A
Power consumption (W) =
= 1.0(W)
1.5(V)-1.2(V)
× 4.0(A)
www.rohm.com
? 2010 ROHM Co., Ltd. All rights reserved.
16/20
2010.04 - Rev.C
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5210-2.9BMM TR | IC REG LDO 2.9V .15A 8-MSOP |
| ESC44DREH-S13 | CONN EDGECARD 88POS .100 EXTEND |
| MIC5330-GGYML TR | IC REG LDO 1.8V .3A 8MLF |
| ABC25DRTS-S13 | CONN EDGECARD 50POS .100 EXTEND |
| MIC2211-YMYML TR | IC REG LDO 1.9V/2.8V 10-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD3509MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:Nch FET Ultra LDO for PC Chipsets |
| BD3509MUV_10 | 制造商:ROHM 制造商全称:Rohm 功能描述:Nch FET Ultra LDO for PC Chipsets |
| BD3509MUV-E2 | 功能描述:低压差稳压器 - LDO ULTRA LO DROPOUT REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BD350S | 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:THROUGH HOLE SCHOTTKY BARRIER RECTIFIERS |
| BD350T | 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:THROUGH HOLE SCHOTTKY BARRIER RECTIFIERS |
发布紧急采购，3分钟左右您将得到回复。