参数资料
型号: BD6210HFP-TR
厂商: Rohm Semiconductor
文件页数: 10/21页
文件大小: 0K
描述: IC H-BRIDGE DVR 7V 1CH .5A HRP7
特色产品: H-Bridge Driver IC
标准包装: 1
应用: 直流电机驱动器
输出数: 1
电流 - 输出: 500mA
电源电压: 3 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: TO-263-8,D²Pak(7 引线+接片),TO-263CA
供应商设备封装: HRP7
包装: 标准包装
其它名称: BD6210HFP-DKR
BD6210HFP-DKR-ND
BD6210HFPDKR
BD621xxx Series
● Functional Descriptions
1) Operation modes
Table 4 Logic table
Datasheet
FIN
RIN
VREF
OUT1
OUT2
Operation
a
b
c
d
e
f
g
h
i
j
L
H
L
H
PWM
L
H
PWM
H
L
L
L
H
H
L
PWM
PWM
H
L
H
X
VCC
VCC
X
VCC
VCC
VCC
VCC
Option
Option
Hi-Z*
H
L
L
H
__________
PWM
__________
PWM
L
H
__________
PWM
Hi-Z*
L
H
L
__________
PWM
H
L
__________
PWM
__________
PWM
H
Stand-by (idling)
Forward (OUT1 > OUT2)
Reverse (OUT1 < OUT2)
Brake (stop)
Forward (PWM control mode A)
Reverse (PWM control mode A)
Forward (PWM control mode B)
Reverse (PWM control mode B)
Forward (VREF control)
Reverse (VREF control)
* Hi-Z i: all output transistors are off. Please note that this is the state of the connected diodes, which differs from that of the mechanical relay.
X : Don’t care
a) Stand-by mode
Stand-by operates independently with the VREF pin voltage. In stand-by mode, all internal circuits are turned off,
including the output power transistors. Motor output goes to high impedance. When the system is switched to
stand-by mode while the motor is running, the system enters an idling state because of the body diodes. However,
when the system switches to stand-by from any other mode (except the brake mode), the control logic remains in
the high state for at least 50μs before shutting down all circuits.
b) Forward mode
This operating mode is defined as the forward rotation of the motor when the OUT1 pin is high and OUT2 pin is low.
When the motor is connected between the OUT1 and OUT2 pins, the current flows from OUT1 to OUT2. To operate
in this mode, connect the VREF pin to the VCC pin.
c) Reverse mode
This operating mode is defined as the reverse rotation of the motor when the OUT1 pin is low and OUT2 pin is high.
When the motor is connected between the OUT1 and OUT2 pins, the current flows from OUT2 to OUT1. To operate
in this mode, connect the VREF pin to the VCC pin.
d) Brake mode
This operating mode is used to quickly stop the motor (short circuit brake). It differs from the stand-by mode
because the internal control circuit is operating in the brake mode. Please switch to stand-by mode (rather than the
brake mode) to save power and reduce consumption.
OFF
OFF
ON
OFF OFF
ON
OFF
OFF
M
M
M
M
OFF
OFF OFF
ON
ON
OFF
ON
ON
a) Stand-by mode
b) Forward mode
c) Reverse mode
d) Brake mode
Fig.30 Four basic operations (output stage)
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
10/18
TSZ02201-0P2P0B300070-1-2
25.Dec.2012 Rev.002
相关PDF资料
PDF描述
H8PPH-1436M DIP CABLE - HDP14H/AE14M/HDP14H
H6PPH-1436M DIP CABLE - HDP14H/AE14M/HDP14H
H2MXH-2436M DIP CABLE - HDM24H/AE24M/X
H2MXS-2436M DIP CABLE - HDM24S/AE24M/X
M1DXK-1036R IDC CABLE - MKR10K/MC10M/X
相关代理商/技术参数
参数描述
BD6211 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.)
BD62110AEFJ-E2 功能描述:36V 1 CH DC BRUSH MOTOR DRIVERS 制造商:rohm semiconductor 系列:- 包装:剪切带(CT) 零件状态:在售 电机类型 - 步进:- 电机类型 - AC,DC:有刷直流 功能:驱动器 - 全集成,控制和功率级 输出配置:半桥(2) 接口:PWM 技术:DMOS 步进分辨率:- 应用:打印机 电流 - 输出:700mA 电压 - 电源:8 V ~ 28 V 电压 - 负载:8 V ~ 28 V 工作温度:-25°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:8-SOIC(0.154",3.90mm 宽)裸露焊盘 供应商器件封装:8-HTSOP-J 标准包装:1
BD6211F 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor
BD6211F-E2 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 7V max 1 Chan 1.0A 1.0ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
BD6211F-E2-CUT TAPE 制造商:ROHM 功能描述:BD6211F Series Single Output 7 V 1 A Surface Mount H-Bridge Driver - SOP-8