- 您现在的位置：买卖IC网 > PDF目录16667 > BD6210HFP-TR (Rohm Semiconductor)IC H-BRIDGE DVR 7V 1CH .5A HRP7 PDF资料下载
参数资料
| 型号： | BD6210HFP-TR |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 12/21页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE DVR 7V 1CH .5A HRP7 |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 应用： | 直流电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | 500mA |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-8，D²Pak（7 引线+接片），TO-263CA |
| 供应商设备封装： | HRP7 |
| 包装： | 标准包装 |
| 其它名称： | BD6210HFP-DKR BD6210HFP-DKR-ND BD6210HFPDKR |
BD621xxx Series
Datasheet
i) j) VREF control mode
The built-in VREF duty cycle conversion circuit provides a duty cycle corresponding to the voltage of the VREF pin
and the VCC voltage. The function offers the same level of control as the high voltage output setting function in
previous models. The duty cycle is calculated by the following equation.
DUTY ≈ VREF [V] / VCC [V]
For example, if VCC voltage is 5V and VREF pin voltage is 3.75V, the duty cycle is about 75 percent. However,
please note that the duty cycle might be limited by the range of the VREF pin voltage (Refer to the operating
conditions, shown on page 2). The PWM carrier frequency in this mode is 25kHz (nominal), and the switching
operation is the same as the PWM control modes. When operating in this mode, do not input a PWM signal to the
FIN and RIN pins. In addition, establish a current path for the recovery current from the motor, by connecting a
bypass capacitor (10μF or more is recommended) between VCC and ground.
VCC
VREF
0
FIN
RIN
OUT1
OUT2
Fig.35 VREF control operation (timing chart)
2) Cross-conduction protection circuit
In the full bridge output stage, when the upper and lower transistors are turned on at the same time during high to low
or low to high transition, an inrush current flows from the power supply to ground, resulting to a loss. This circuit
eliminates the inrush current by providing a dead time (about 400ns, nominal) during the transition.
3) Output protection circuits
a) Under voltage lock out (UVLO) circuit
To ensure the lowest power supply voltage necessary to operate the controller, and to prevent under voltage
malfunctions, a UVLO circuit has been built into this driver. When the power supply voltage falls to 2.3V (nominal) or
below, the controller forces all driver outputs to high impedance. When the voltage rises to 2.5V (nominal) or above,
the UVLO circuit ends the lockout operation and returns the chip to normal operation.
b) Over voltage protection (OVP) circuit
When the power supply voltage exceeds 7.3V (nominal), the controller forces all driver outputs to high impedance.
The OVP circuit is released and its operation ends when the voltage drops back to 6.8V (nominal) or below. This
protection circuit does not work in the stand-by mode. Also, note that this circuit is supplementary, and thus if it is
asserted, the absolute maximum rating will have been exceeded. Therefore, do not continue to use the IC after this
circuit is activated, and do not operate the IC in an environment where activation of the circuit is assumed.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
12/18
TSZ02201-0P2P0B300070-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| H8PPH-1436M | DIP CABLE - HDP14H/AE14M/HDP14H |
| H6PPH-1436M | DIP CABLE - HDP14H/AE14M/HDP14H |
| H2MXH-2436M | DIP CABLE - HDM24H/AE24M/X |
| H2MXS-2436M | DIP CABLE - HDM24S/AE24M/X |
| M1DXK-1036R | IDC CABLE - MKR10K/MC10M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6211 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
| BD62110AEFJ-E2 | 功能描述:36V 1 CH DC BRUSH MOTOR DRIVERS 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:在售 电机类型 - 步进:- 电机类型 - AC，DC:有刷直流 功能:驱动器 - 全集成，控制和功率级 输出配置:半桥（2） 接口:PWM 技术:DMOS 步进分辨率:- 应用:打印机 电流 - 输出:700mA 电压 - 电源:8 V ~ 28 V 电压 - 负载:8 V ~ 28 V 工作温度:-25°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽）裸露焊盘 供应商器件封装:8-HTSOP-J 标准包装:1 |
| BD6211F | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
| BD6211F-E2 | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 7V max 1 Chan 1.0A 1.0ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| BD6211F-E2-CUT TAPE | 制造商:ROHM 功能描述:BD6211F Series Single Output 7 V 1 A Surface Mount H-Bridge Driver - SOP-8 |
发布紧急采购，3分钟左右您将得到回复。