- 您现在的位置：买卖IC网 > PDF目录16651 > BD6226FP-E2 (Rohm Semiconductor)IC H-BRIDGE DRIVER 2CH 1A HSOP25 PDF资料下载
参数资料
| 型号： | BD6226FP-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 11/22页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE DRIVER 2CH 1A HSOP25 |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 应用： | 直流电机驱动器 |
| 输出数： | 2 |
| 电流 - 输出： | 1A |
| 电源电压： | 6 V ~ 15 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-SOP（0.213"，5.40mm）+ 2 翼片 |
| 供应商设备封装： | 25-HSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD6226FP-E2DKR |
BD622xxx Series
● Functional Descriptions
Datasheet
1)
Operation modes
Table 5 Logic table
FIN
RIN
VREF
OUT1
OUT2
Operation
a
b
c
d
e
f
g
h
i
j
L
H
L
H
PWM
L
H
PWM
H
L
L
L
H
H
L
PWM
PWM
H
L
H
X
VCC
VCC
X
VCC
VCC
VCC
VCC
Option
Option
Hi-Z*
H
L
L
H
__________
PWM
__________
PWM
L
H
__________
PWM
Hi-Z*
L
H
L
__________
PWM
H
L
__________
PWM
__________
PWM
H
Stand-by (idling)
Forward (OUT1 > OUT2)
Reverse (OUT1 < OUT2)
Brake (stop)
Forward (PWM control mode A)
Reverse (PWM control mode A)
Forward (PWM control mode B)
Reverse (PWM control mode B)
Forward (VREF control)
Reverse (VREF control)
* Hi-Z : all output transistors are off. Please note that this is the state of the connected diodes,
which differs from that of the mechanical relay.
X : Don’t care
a) Stand-by mode
Stand-by operates independently with the VREF pin voltage. In stand-by mode, all internal circuits are turned off,
including the output power transistors. Motor output goes to high impedance. When the system is switched to
stand-by mode while the motor is running, the system enters an idling state because of the body diodes. However,
when the system switches to stand-by from any other mode (except the brake mode), the control logic remains in the
high state for at least 50μs before shutting down all circuits.
b) Forward mode
This operating mode is defined as the forward rotation of the motor when the OUT1 pin is high and OUT2 pin is low.
When the motor is connected between the OUT1 and OUT2 pins, the current flows from OUT1 to OUT2. To operate
in this mode, connect the VREF pin to the VCC pin.
c) Reverse mode
This operating mode is defined as the reverse rotation of the motor when the OUT1 pin is low and OUT2 pin is high.
When the motor is connected between the OUT1 and OUT2 pins, the current flows from OUT2 to OUT1. To operate
in this mode, connect the VREF pin to the VCC pin.
d) Brake mode
This operating mode is used to quickly stop the motor (short circuit brake). It differs from the stand-by mode because
the internal control circuit is operating in the brake mode. Please switch to stand-by mode (rather than the brake
mode) to save power and reduce consumption.
OFF
OFF
ON
OFF OFF
ON
OFF
OFF
M
M
M
M
OFF
OFF OFF
ON
ON
OFF
ON
ON
a) Stand-by mode
b) Forward mode
c) Reverse mode
d) Brake mode
Fig.33 Four basic operations (output stage)
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
11/19
TSZ02201-0P2P0B300080-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| EEC20DRAH-S734 | CONN EDGECARD 40POS .100 R/A PCB |
| ELC-16B151L | COIL CHOKE 150UH RADIAL |
| H1AXH-3036M | IDC CABLE - HSC30H/AE30M/X |
| VI-B4T-EW | CONVERTER MOD DC/DC 6.5V 100W |
| VI-BT3-EX | CONVERTER MOD DC/DC 24V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6227 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (18V max.) |
| BD622X-E | 制造商:ROHM 制造商全称:Rohm 功能描述:DC Brush Motor Drivers (18V max.) |
| BD6230 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD6230_09 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD6230F | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
发布紧急采购，3分钟左右您将得到回复。