- 您现在的位置：买卖IC网 > PDF目录16651 > BD6226FP-E2 (Rohm Semiconductor)IC H-BRIDGE DRIVER 2CH 1A HSOP25 PDF资料下载
参数资料
| 型号： | BD6226FP-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 13/22页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE DRIVER 2CH 1A HSOP25 |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 应用： | 直流电机驱动器 |
| 输出数： | 2 |
| 电流 - 输出： | 1A |
| 电源电压： | 6 V ~ 15 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-SOP（0.213"，5.40mm）+ 2 翼片 |
| 供应商设备封装： | 25-HSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD6226FP-E2DKR |
BD622xxx Series
Datasheet
i) j) VREF control mode
The built-in VREF duty cycle conversion circuit provides a duty cycle corresponding to the voltage of the VREF pin
and the VCC voltage. The function offers the same level of control as the high voltage output setting function in
previous models. The duty cycle is calculated by the following equation.
DUTY ≈ VREF [V] / VCC [V]
For example, if VCC voltage is 12V and VREF pin voltage is 9V, the duty cycle is about 75 percent. However, please
note that the duty cycle might be limited by the range of the VREF pin voltage (Refer to the operating conditions,
shown on page 2). The PWM carrier frequency in this mode is 25kHz (nominal), and the switching operation is the
same as the PWM control modes. When operating in this mode, do not input a PWM signal to the FIN and RIN pins.
In addition, establish a current path for the recovery current from the motor, by connecting a bypass capacitor (10μF
or more is recommended) between VCC and ground.
VCC
VREF
0
FIN
RIN
OUT1
OUT2
Fig.38 VREF control operation (timing chart)
2)
3)
Cross-conduction protection circuit
In the full bridge output stage, when the upper and lower transistors are turned on at the same time during high to
low or low to high transition, an inrush current flows from the power supply to ground, resulting to a loss. This circuit
eliminates the inrush current by providing a dead time (about 400ns, nominal) during the transition.
Output protection circuits
a) Under voltage lock out (UVLO) circuit
To ensure the lowest power supply voltage necessary to operate the controller, and to prevent under voltage
malfunctions, a UVLO circuit has been built into this driver. When the power supply voltage falls to 5.0V (nominal) or
below, the controller forces all driver outputs to high impedance. When the voltage rises to 5.5V (nominal) or above,
the UVLO circuit ends the lockout operation and returns the chip to normal operation.
b) Over voltage protection (OVP) circuit
When the power supply voltage exceeds 30V (nominal), the controller forces all driver outputs to high impedance.
The OVP circuit is released and its operation ends when the voltage drops back to 25V (nominal) or below. This
protection circuit does not work in the stand-by mode. Also, note that this circuit is supplementary, and thus if it is
asserted, the absolute maximum rating will have been exceeded. Therefore, do not continue to use the IC after this
circuit is activated, and do not operate the IC in an environment where activation of the circuit is assumed.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
13/19
TSZ02201-0P2P0B300080-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| EEC20DRAH-S734 | CONN EDGECARD 40POS .100 R/A PCB |
| ELC-16B151L | COIL CHOKE 150UH RADIAL |
| H1AXH-3036M | IDC CABLE - HSC30H/AE30M/X |
| VI-B4T-EW | CONVERTER MOD DC/DC 6.5V 100W |
| VI-BT3-EX | CONVERTER MOD DC/DC 24V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6227 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (18V max.) |
| BD622X-E | 制造商:ROHM 制造商全称:Rohm 功能描述:DC Brush Motor Drivers (18V max.) |
| BD6230 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD6230_09 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD6230F | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
发布紧急采购，3分钟左右您将得到回复。