- 您现在的位置：买卖IC网 > Datasheet目录315 > BD6583MUV-AE2 (Rohm Semiconductor)IC LED DRIVER WHIT BCKLGT 24VQFN Datasheet资料下载
参数资料
| 型号： | BD6583MUV-AE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 19/35页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER WHIT BCKLGT 24VQFN |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 22 V |
| 输出电压： | 43V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | VQFN024V4040 |
| 包装： | 标准包装 |
| 工作温度： | -30°C ~ 85°C |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD6583MUV-ADKR BD6583MUV-ADKR-ND BD6583MUV-AE2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
BD6583MUV-A
Datasheet
● Brightness control
There are two dimming method is available, first method is analog dimming that apply analog voltage to ISET terminal, and
second method is PWM control via digital dimming of PWMPOW or PWMDRV. Because each method has the different
merit, please choose a suitable method for the application of use.
Two techniques can be used as digital dimming by the PWM control One is PWM control of current driver, the other is PWM
control of power control.
As these two characteristics are shown in the below, selects to PWM control process comply with application.
?Efficiency emphasis in the low brightness which has an influence with the battery life
?
2)
Power
control
PWM
control
?LED current dispersion emphasis in the PWM brightness control
?
1)
Current
driver
PWM
control
(Reference)
PWM regulation process
Current driver
Power control
Efficiency of LED current 0.5mA
(PWM Duty=2.5%)
70%
93%
PWM frequency 200Hz
Limit dispersion capability of low duty
0.2%
0.5%
1) Current driver PWM control is controlled by providing PWM signal to PWMDRV, as it is shown Figure 42.
The current set up with ISETH is chosen as the H section of PWMDRV and the current is off as the L section. Therefore, the
average LED current is increasing in proportion to duty cycle of PWMDRV signal. This method that it lets internal circuit and
DC/DC to work, because it becomes to switch the driver, the current tolerance is a few when the PWM brightness is
adjusted, it makes it possible to brightness control until 20μs (MIN0.4% at 200Hz). And, don't use for the brightness control,
because effect of ON/OFF changeover is big under 20μs ON time and under 20μs OFF time. There is no effect of ON/OFF
changeover at 0% and 100%, so there is no problem on use. Typical PWM frequency is 100Hz to 10kHz. When resistance is
set as ISET, RSTB sets H ? L, so the starting current may be effective, after RSTB sets L ? H, it becomes PWM of the
starting current and PWM of ISETH setting current to PWM two times.
PWMDRV
LED current
Coil current
IC’s active current
ON
ON
ON
OFF
OFF
OFF
ON
Figure 42.
2) Power control PWM control is controlled by providing PWM signal to PWMPOW, as it is shown Figure 43. The current
setting set up with PWMDRV logic is chosen as the H section and the current is off as the L section. Therefore, the
average LED current is increasing in proportion to duty cycle of PWMPOW signal. This method is, because IC can be
power-off at off-time, the consumption current can be suppress, and the high efficiency can be available, so it makes it
possible to brightness control until 50μs (MIN1% at 200Hz). And, don't use for the brightness control, because effect of
power ON/OFF time changeover is big under 50μs ON time and under 50μs OFF time. There is no effect of ON/OFF
changeover at 0% and 100%, so there is no problem on use.
Typical PWM frequency is 100Hz to 1kHz. Also, PWM can't control RSTB and PWMPOW at the same time.
After RSTB sets H, control PWM only PWMPOW.
PWMPOW
LED current
Coil current
IC’s active current
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
ON
ON
ON
ON
Figure 43.
19/32
OFF
OFF
OFF
OFF
TSZ02201-0G3G0C400180-1-2
03.Dec.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD6586MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD6592MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD7844AEFV-E2 | IC LED DISPLAY DVR 5V 28-HTSSOP |
| BD8105FV-E2 | IC LED DVR SERIAL PAR 20-SSOP |
| BD8112EFV-ME2 | IC LED DRIVER 24-VSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6583MUV-E2 | 功能描述:LED照明驱动器 72 LEDs 2.7-22V 43V Max Out 25mA Out RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| BD6586MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit |
| BD6586MUV_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
| BD6586MUV-E2 | 功能描述:LED照明驱动器 24 LEDs 2.7-5.5V 24V Max Out 25mA Out RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| BD6590MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
发布紧急采购，3分钟左右您将得到回复。