- 您现在的位置：买卖IC网 > Datasheet目录315 > BD6583MUV-AE2 (Rohm Semiconductor)IC LED DRIVER WHIT BCKLGT 24VQFN Datasheet资料下载
参数资料
| 型号： | BD6583MUV-AE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 30/35页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER WHIT BCKLGT 24VQFN |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 22 V |
| 输出电压： | 43V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | VQFN024V4040 |
| 包装： | 标准包装 |
| 工作温度： | -30°C ~ 85°C |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD6583MUV-ADKR BD6583MUV-ADKR-ND BD6583MUV-AE2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页
BD6583MUV-A
Datasheet
● Operational Notes
(1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any
special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety
measures including the use of fuses, etc.
(2) Operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The
electrical characteristics are guaranteed under the conditions of each parameter.
(3) Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown due
to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply
terminal.
(4) Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard,
for the digital block power supply and the analog block power supply, even though these power supplies has the same
level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing
the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns.
For the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal.
At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be
used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant.
(5) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient.
(6) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can
break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between
the terminal and the power supply or the GND terminal, the ICs can break down.
(7) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
(8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the
jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In
addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention
to the transportation and the storage of the set PCB.
(9) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the
input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals
a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage
to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
(10) Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the
small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
(11) External capacitor
In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a
degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc.
(12) Thermal shutdown circuit (TSD)
When junction temperatures become 175°C (typ) or higher, the thermal shutdown circuit operates and turns a switch OFF.
The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed
at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the
LSI assuming its operation.
(13) Thermal design
Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in
actual states of use.
(14) Selection of coil
Select the low DCR inductors to decrease power loss for DC/DC converter.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
30/32
TSZ02201-0G3G0C400180-1-2
03.Dec.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD6586MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD6592MUV-E2 | IC LED DRVR WHITE BCKLGT 24-VQFN |
| BD7844AEFV-E2 | IC LED DISPLAY DVR 5V 28-HTSSOP |
| BD8105FV-E2 | IC LED DVR SERIAL PAR 20-SSOP |
| BD8112EFV-ME2 | IC LED DRIVER 24-VSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6583MUV-E2 | 功能描述:LED照明驱动器 72 LEDs 2.7-22V 43V Max Out 25mA Out RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| BD6586MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit |
| BD6586MUV_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
| BD6586MUV-E2 | 功能描述:LED照明驱动器 24 LEDs 2.7-5.5V 24V Max Out 25mA Out RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| BD6590MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type) |
发布紧急采购，3分钟左右您将得到回复。