- 您现在的位置：买卖IC网 > PDF目录19400 > BD7851FP-E2 (Rohm Semiconductor)IC LED DRIVER LINEAR 25-HSOP PDF资料下载
参数资料
| 型号： | BD7851FP-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 16/18页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 25-HSOP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 线性 |
| 输出数： | 16 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 输出电压： | 10V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-SOP（0.213"，5.40mm）+ 2 翼片 |
| 供应商设备封装： | 25-HSOP |
| 包装： | 标准包装 |
| 工作温度： | -30°C ~ 85°C |
| 产品目录页面： | 1372 (CN2011-ZH PDF) |
| 其它名称： | BD7851FP-E2DKR |
BU2050F,BU2092F,BU2092FV,BU2099FV,BD7851FP,BU2152FS
Technical Note
7/24
www.rohm.com
2009.06 - Rev.A
2009 ROHM Co., Ltd. All rights reserved.
【BU2050F】
●Pin descriptions
Pin No.
Pin Name
Function
1
P3
Parallel Data Output
2
P4
3
P5
4
VSS
GND
5
P6
Parallel Data Output
6
P7
7
P8
8
DATA
Serial Data Input
9
CLK
Clock Signal Input
10
STB
Strobe Signal Input
In case of “L”, the data of shift register outputs.
In case of “H”, all parallel outputs and data of latch circuit do not change.
11
CLR
Reset Signal Input
In case of “L”, the data of latch circuit reset, and all parallel output (P1～P8) can be L.
Normally CLR=H
12
P1
Parallel Data output
13
P2
14
VDD
Power Supply
●Timing chart
Fig. 2
1. After the power is turned on and the voltage is stabilized, STB should be activated, after clocking 8 data bits into the
DATA pin.
2. Pn parallel output data of the shift register is set after the 8
th clock by the STB.
3. Since the STB is level latch, data is retained in the “L” section and renewed in the “H” section of the STB.
［Function explanation］
·
A latch circuit has the reset function, which is common in all bits. In case of CLR terminal is “L”, the latch
circuit is reset non-synchronously without the other input condition, and all parallel output can be “L”.
·
A serial data inputted from DATA terminal is read in shift register with synchronized rising of clock.
In case of STB is “L” (CLR is ”H”), transmit the data which read in the shift register to latch circuit, and
outputs from the parallel data output terminal (P1～P8).
In case of STB is “H”, all parallel outputs and the data of latch do not change.
CLK
STB
DATA
DATA8
DATA7
DATA6
DATA2
DATA1
Pn
Previous DATA
DATA
CLR
“L”
相关PDF资料 |
PDF描述 |
|---|---|
| EEC05DREI-S93 | CONN EDGECARD 10POS .100 EYELET |
| RW2-0512D/SMD | CONV DC/DC 2W 4.5-9VIN +/-12VOUT |
| TRJD686M016RRJ | CAP TANT 68UF 16V 20% 2917 |
| ADSP-21479BCPZ-1A | IC DSP SHARK 200MHZ 88LFCSP |
| MLP2520S4R7S | INDUCTOR MULTILAYER 4.7UH 1008 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD786 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | DARLINGTON | PNP | 45V V(BR)CEO | 4A I(C) | TO-127VAR |
| BD7861KN-E2 | 制造商:ROHM 制造商全称:Rohm 功能描述:Mixer & Selector IC with PCM CODEC and 16bit D/A Converter |
| BD787 | 功能描述:两极晶体管 - BJT 4A 60V 15W NPN RoHS:否 制造商:STMicroelectronics 配置: 晶体管极性:PNP 集电极—基极电压 VCBO: 集电极—发射极最大电压 VCEO:- 40 V 发射极 - 基极电压 VEBO:- 6 V 集电极—射极饱和电压: 最大直流电集电极电流: 增益带宽产品fT: 直流集电极/Base Gain hfe Min:100 A 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PowerFLAT 2 x 2 |
| BD787/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Complementary Plastic Silicon Power Transistors |
| BD787_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Complementary Plastic Silicon Power Transistors |
发布紧急采购，3分钟左右您将得到回复。