参数资料
| 型号： | BD95513MUV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 32VQFN |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.7 V ~ 5 V |
| 输入电压： | 4.5 V ~ 28 V |
| PWM 型： | 混合物 |
| 频率 - 开关： | 200kHz ~ 600kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | VQFN032V5050 |
| 产品目录页面： | 1373 (CN2011-ZH PDF) |
| 其它名称： | BD95513MUV-E2DKR |
BD95513MUV
Technical Note
● Pin Descriptions
? V CC
This pin supplies power to the IC’s internal circuitry, excluding the FET driver. The input supply voltage range is
4.5 to 5.5V, with a maximum current draw of 900μA. This pin should be bypassed with a capacitance of approximately 0.1μF.
? EN
Enables or disables the switching regulator. When the voltage on this pin reaches 2.3 V or higher, the internal switching
regulator is turned on. At voltages less than 0.8 V, the regulator is turned off.
? V DD
This pin supplies power to the low side of the FET driver, as well as to the bootstrap diode. As the diode draws its peak
current when switching on or off, this pin should be bypassed with a capacitance of approximately 1 μF.
? V REG
Output pin from the 5 V linear regulator. This pin also supplies power to the internal driver and control circuitry.
V REG standby function is controlled by the CTL pin. The output supplies 5V at 100 mA and should be bypassed to ground
using a 10 μF capacitor with a rating of X5R or X7R.
? EXTV CC
External power supply input for the linear regulator. When the voltage on the EXTV CC pin exceeds 4.4 V, the regulator
uses it in conjunction with other power sources to supply V REG . Leave the EXTV CC pin floating when not in use.
? REF
Reference voltage output pin. The reference voltage is set internally by the IC to 0.7 V, and the IC works to keep V REF
approximately equal to V FB . Variations in voltage levels on this pin affect the output voltage, so the pin should be
bypassed with a 100 pF ~ 0.1 μF ceramic capacitor.
? SS
Soft start/stop pin. When EN is set high, the capacitor between the internal current source and SS-GND controls the
startup time of the IC. When the voltage on the SS pin is lower than the REF output voltage (0.7 V), the output voltage is
held at the same voltage as the SS pin.
? AV IN
The BD95513MUV controls the duty cycle and output voltage based upon the input voltage at this pin, so voltage
variations or oscillations on this line can cause operation to become unstable. This pin also acts as the voltage input for
the switching block, so insufficient coupling impedance can also cause operation to become unstable. Therefore, this
line should be bypassed with either a power capacitor or RC filter.
? FS
Frequency-adjusting resistance input pin.
Attaching a resistance of 30 k ~ 100 k ? adjusts the switching frequency from
mode.
high, SLLM
200 kHz ~ 1 MHz.
? BOOT
This pin serves as the power source for the high side of the FET driver. A bootstrap diode is integrated within the IC.
The maximum voltage on this pin should not exceed +30 V vs. GND or +7 V vs. SW. When operating the switching
regulator, the operation of the bootstrap circuitry causes the BOOT voltage to swing from (V IN + V DD ) ~ V DD .
? PGOOD
Power good indicator. This open-drain output should be connected via a 100 k ? pull-up resistor.
? MODE
Mode selection pin. When low, the IC functions in forced-continuous mode; at voltages from 0V ~ 3V, QLLM mode; when
TM
? CTL
Linear regulator control pin. When voltage is 2.3 V or higher, a logic HIGH is recognized and the internal regulator
(V REG = 5 V) is switched on. At voltages of 0.8 V or lower, a logic LOW is recognized and the regulator is switched off.
However, even if EN is logic HIGH, the switching regulator will not operate if CTL is logic LOW.
? FB
Output voltage feedback input. V FB is held at 0.7 V by the IC.
? SW
Output from the switching regulator to the inductor. This output swings from V IN ~ GND. The trace from the output to
the inductor should be as short and wide as possible.
? V OUT
Voltage output discharge pin. When EN is off, this output is pulled low.
? V IN
Power supply input. The IC can accept any input from 4.5 V to 28 V. This pin should be bypassed directly to ground by
a power capacitor.
? PGND
Power ground terminal.
www.rohm.com
? 2010 ROHM Co., Ltd. All rights reserved.
9/17
2010.10- Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| BD9701T-V5 | IC REG BUCK ADJ 1.5A TO220FP |
| BD9739KN-E2 | IC REG SW BUILT IN FET 64UQFN |
| BD9763FVM-TR | IC REG CTRLR BST PWM 8-MSOP |
| BD9775FV-E2 | IC REG CTRLR BUCK PWM 28-SSOP |
| BD9778HFP-TR | IC REG BUCK ADJ 2A HRP7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD95514MUV | 制造商:ROHM 制造商全称:Rohm 功能描述:FET Integrated Switching Regulator for DDR-SDRAM Cores |
| BD95514MUV-E2 | 制造商:ROHM Semiconductor 功能描述:CONV DC-DC SINGLE NON-INV/INV/STEP UP/STEP DOWN 4.5V TO 28V - Tape and Reel |
| BD9555FVM-CGTR | 功能描述:50V 1CH TIMER IC FOR AUTOMOTIVE 制造商:rohm semiconductor 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:在售 类型:计时器控制 计数:- 电压 - 电源:4.5 V ~ 42 V 电流 - 电源:1mA 工作温度:-40°C ~ 125°C 封装/外壳:8-VSSOP，8-MSOP（0.110"，2.80mm 宽） 供应商器件封装:8-MSOP 安装类型:表面贴装 标准包装:1 |
| BD956 | 制造商:TT Electronics/ Semelab 功能描述:TRANSISTOR PNP TO-220 制造商:TT Electronics/ Semelab 功能描述:TRANSISTOR, PNP, TO-220 |
| BD956 | 制造商:TT Electronics/ Semelab 功能描述:TRANSISTOR PNP TO-220 |
发布紧急采购，3分钟左右您将得到回复。