- 您现在的位置：买卖IC网 > PDF目录4224 > BR24L01AFVJ-WE2 (Rohm Semiconductor)IC EEPROM SER 1KBIT I2C 8TSSOP PDF资料下载
参数资料
| 型号： | BR24L01AFVJ-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 34/41页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM SER 1KBIT I2C 8TSSOP |
| 标准包装： | 2,500 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K (128 x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-TSSOP-BJ |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页
BR24L □□ -W Series,BR24S □□□ -W Series
Technical Note
● I/O peripheral circuit
○ Pull up resistance of SDA terminal
SDA is NMOS open drain, so requires pull up resistance. As for this resistance value (R PU ), select an appropriate value to
this resistance value from microcontroller V IL , I L , and V OL -I OL characteristics of this IC. If R PU is large, action frequency is
limited. The smaller the R PU , the larger the consumption current at action.
○ Maximum value of R PU
The maximum value of R PU is determined by the following factors.
(1)SDA rise time to be determined by the capacitance (CBUS) of bus line of R PU and SDA should be tR or below.
And AC timing should be satisfied even when SDA rise time is late.
(2)The bus electric potential A to be determined by input leak total (I L ) of device connected to bus output of 'H' to SDA
bus and R PU should sufficiently secure the input 'H' level (V IH ) of microcontroller and EEPROM including recommended
noise margin 0.2Vcc.
Vcc - I L R PU - 0.2Vcc ≧ V IH
Microcontroller
BR24SXX
∴
R PU
≦
0.8V CC - V IH
I L
Ex.) When Vcc = 3V, I L =10 μ A, V IH = 0.7Vcc
from(2)
10×10
R PU ≦
0.8×3 - 0.7×3
-6
≦ 300 ［ k ? ］
○ Minimum value of R PU
The minimum value of R PU is determined by the following factors.
(1)When IC outputs LOW, it should be satisfied that V OLMAX =0.4V
and I OLMAX =3mA.
Bus line
capacity
CBUS
Fig.49 I/O circuit diagram
V CC - V OL
R PU
≦
I OL
∴
R PU
≧
V CC - V OL
I OL
(2)V OLMAX =0.4V should secure the input 'L' level (V IL ) of microcontroller and EEPROM including recommended noise margin 0.1Vcc.
V OLMAX ≦ V IL -0.1 Vcc
Ex.) When Vcc= 3V, V OL 0.4V, I OL =3mA, microcontroller, EEPROM V IL =0.3Vcc
from(1),
R PU
≧
3 － 0.4
3×10
≧
867
［ ? ］
And
V OL =0.4 ［ V ］
V IL =0.3 × 3
=0.9 ［ V ］
Therefore, the condition (2) is satisfied.
○ Pull up resistance of SCL terminal
When SCL control is made at CMOS output port, there is no need, but in the case there is timing where SCL becomes
'Hi-Z', add a pull up resistance. As for the pull up resistance, one of several k ? ~ several ten k ? is recommended in
consideration of drive performance of output port of microcontroller.
● A0, A1, A2, WP process
○ Process of device address terminals (A0,A1,A2)
Check whether the set device address coincides with device address input sent from the master side or not, and select
one among plural devices connected to a same bus. Connect this terminal to pull up or pull down, or Vcc or GND. And,
pins(Don't use PIN) not used as device address may be set to any of 'H' , 'L', and 'Hi-Z'.
Types with Don't use PIN BR24S08F/FJ/FV/FVT/FVM/FVJ/NUX-W A0, A1
BR24S16F/FJ/FV/FVT/FVM/FVJ/NUX-W A0, A1, A2
○ Process of WP terminal
WP terminal is the terminal that prohibits and permits write in hardware manner. In 'H' status, only READ is available and
WRITE of all address is prohibited. In the case of 'L', both are available. In the case of use it as an ROM, it is
recommended to connect it to pull up or Vcc. In the case to use both READ and WRITE, control WP terminal or connect
it to pull down or GND.
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
34/40
2009.09 - Rev.D
相关PDF资料 |
PDF描述 |
|---|---|
| FMC15DRES-S93 | CONN EDGECARD 30POS .100 EYELET |
| XC4VLX60-10FFG668C | IC FPGA VIRTEX-4 60K 668-FCBGA |
| RSC65DRYN-S734 | CONN EDGECARD 130PS DIP .100 SLD |
| XC5VLX50-1FF676I | IC FPGA VIRTEX-5 50K 676FBGA |
| BR93L46-W | IC EEPROM 1KBIT 2MHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BR24L01AFVM-W | 制造商:ROHM 制造商全称:Rohm 功能描述:128】8 bit electrically erasable PROM |
| BR24L01AFVM-WTR | 功能描述:电可擦除可编程只读存储器 IC 电可擦除可编程只读存储器 SRL 128X8BIT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BR24L01AFVT-W | 制造商:ROHM Semiconductor 功能描述:Memory,EEPROM,1kb(X8),I2C BUS,TSSOP8 |
| BR24L01AFVT-WE2 | 功能描述:电可擦除可编程只读存储器 I2C BUS 1Kbit 1.8-5.5V Supply RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BR24L01AFV-W | 制造商:ROHM Semiconductor 功能描述:EEPROM,1kb,128Wx8b,I2C Bus,SSOP8 |
发布紧急采购，3分钟左右您将得到回复。